Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Splitting Water – Electrolysis Experiment

Splitting Water – Electrolysis Experiment

Is it possible to break water? In a sense, that is what electrolysis does. Electrolysis uses electricity to split water into its two ingredients – hydrogen and oxygen. Try it out with a battery and a couple pencils.
What to do:

Fill the beaker or glass with warm water.

Carefully remove the erasers and metal sleeves so you can sharpen both ends of each pencil.

Cut a piece of the cardboard to fit over the beaker, then punch two holes in the center of the cardboard about an inch apart. Push the pencils through the holes and set them in the glass. They should extend into the water, but not touch the bottom of the glass. The cardboard will hold them in place.

Connect each pencil to the battery with an alligator clip lead attached to the exposed graphite (pencil lead). If you don’t have alligator clip leads, use two lengths of wire and strip an inch of insulation off each end. Wrap the wire around the graphite of each pencil and connect the wires to the battery. You may need to use tape to hold the wires in place.

What’s happening?

As soon as you connect the wires to the battery, you will see bubbles appearing around each of the pencil tips in the water and floating upward. Those bubbles are the components of water—hydrogen and oxygen gas—that have been split apart by the electricity as it travels through the water from one pencil to the other. The pencil attached to the negative terminal of the battery collects hydrogen gas while the one connected to the positive terminal collects oxygen. Does one pencil collect more bubbles than the other? Which one? Why do you think this is? (Hint: Water’s chemical name is H2O because it has two hydrogen atoms to every one oxygen atom.)

Visit Here for more.







 

More Articles to Read

App note: Infrared remote control implementation with MSP430FR4xx
App note: Infrared remote control implementation with MSP430FR4xx
Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown
Blinking Christmas Lights
Blinking Christmas Lights
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adding an “extra sense” with rangefinders
Adding an “extra sense” with rangefinders
This wireless game controller looks like a rug
This wireless game controller looks like a rug
How to run your ESP8266 for years on a battery
How to run your ESP8266 for years on a battery
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Making beats on a tiny Arduino DJ controller
Making beats on a tiny Arduino DJ controller
Qinsi-QS5100 Sn63Pb37 solder profile
Qinsi-QS5100 Sn63Pb37 solder profile
Water Detection System
Water Detection System
Professional Hi-Fi 15W Tube Amplifier circuit
Professional Hi-Fi 15W Tube Amplifier circuit
This Arduino machine will judge how sick your ollies are
This Arduino machine will judge how sick your ollies are
Turn an old payphone into a boombox for ’90s hits
Turn an old payphone into a boombox for ’90s hits
Big F’n 3D printer build
Big F’n 3D printer build
Temperature alarm for boiling milk
Temperature alarm for boiling milk
QuadBot is a 3D-printable walking robot for everyone
QuadBot is a 3D-printable walking robot for everyone

Top


Shares