Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Water Level Controller

Water Level Controller

I n most houses, water is first stored in an underground tank (UGT) and from there it is pumped up to the overhead tank (OHT) located on the roof. People generally switch on the pump when their taps go dry and switch off the pump when the overhead tank starts overflowing. This results in the unnecessary wastage and sometimes non-availability of water in the case of emergency.
The simple circuit presented here makes this system automatic, i.e. it switches on the pump when the water level in the overhead tank goes low and switches it off as soon as the water level reaches a pre-determined level. It also prevents ‘dry run’ of the pump in case the level in the underground tank goes below the suction level.

In the figure, the common probes connecting the underground tank and the overhead tank to +9V supply are marked ‘C’. The other probe in underground tank, which is slightly above the ‘dry run’ level, is marked ‘S’. The low-level and high-level probes in the overhead tank are marked ‘L’ and ‘H’, respectively.

When there is enough water in the underground tank, probes C and S are connected through water. As a result, transistor T1 gets forward biased and starts conducting. This, in turn, switches transistor T2 on. Initially, when the overhead tank is empty, transistors T3 and T5 are in cut-off state and hence pnp transistors T4 and T6 get forward biased via resistors R5 and R6, respectively.

As all series-connected transistors T2, T4, and T6 are forward biased, they conduct to energise relay RL1 (which is also connected in series with transistors T2, T4, and T6). Thus the supply to the pump motor gets completed via the lower set of relay contacts (assuming that switch S2 is on) and the pump starts filling the overhead tank.

Once the relay has energised, transistor T6 is bypassed via the upper set of contacts of the relay. As soon as the water level touches probe L in the overhead tank, transistor T5 gets forward biased and starts conducting. This, in turn, reverse biases transistor T6, which then cuts off. But since transistor T6 is bypassed through the relay contacts, the pump continues to run. The level of water continues to rise.

When the water level touches probe H, transistor T3 gets forward biased and starts conducting. This causes reverse biasing of transistor T4 and it gets cut off. As a result, the relay de-energises and the pump stops. Transistors T4 and T6 will be turned on again only when the water level drops below the position of L probe.

Presets VR1, VR2, and VR3 are to be adjusted in such a way that transistors T1, T3, and T5 are turned on when the water level touches probe pairs C-S, C-H, and C-L, respectively. Resistor R4 ensures that transistor T2 is ‘off’ in the absence of any base voltage. Similarly, resistors R5 and R6 ensure that transistors T4 and T6 are ‘on’ in the absence of any base voltage. Switches S1 and S2 can be used to switch on and switch off, respectively, the pump manually.

You can make and install probes on your own as per the requirement and facilities available. However, we are describing here how the probes were made for this prototype.

Visit Here for more.

 

More Articles to Read

Guide to build your 3.3v power supply
Guide to build your 3.3v power supply
SDR radio breathes life into a 75 year old Marconi CR100
SDR radio breathes life into a 75 year old Marconi CR100
A Time for Ranting!
A Time for Ranting!
Emulate a Commodore 64 keyboard with a modern PC and an Arduino
Emulate a Commodore 64 keyboard with a modern PC and an Arduino
USB2005 and USB97C202 Sharing ATA/ATAPI Drive w/ Another Controller
USB2005 and USB97C202 Sharing ATA/ATAPI Drive w/ Another Controller
Robotic Cat Laser
Robotic Cat Laser
LED traffic light
LED traffic light
Estimating Power for ADSP-BF561 Blackfin® Processors
Estimating Power for ADSP-BF561 Blackfin® Processors
Teach Your Arduino to Switch Itself Off!
Teach Your Arduino to Switch Itself Off!
Control a tracked robot with your mind (or joystick)
Control a tracked robot with your mind (or joystick)

Top




Shares