Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Hope One LED Light GoPro mount

Hope One LED Light GoPro mount

With the dark winter evenings drawing in we are starting to use the bikes more at night than in the day time due to work commitments to try to keep fit.

We purchased a set of Hope One LED lights earlier this year and they come with an easy to use quick release mount but I found a problem when using the light on my cyclocross bike when my Garmin Edge 810 is fitted as the Hope led mount isn’t high enough to clear the Garmin and so a lot of the light is blocked with the Garmin being in the way. It isn’t possible to fit the light under the handlebar as the cables get in the way when turning so I needed to find a way to mount the light so it wouldn’t be blocked by the other accessories on the narrow handlebars.

I use a K-Edge out in front mount for the Garmin and I made an adapter to use my Go Pro Hero cameras under the mount as this seemed to be the ideal location for the Hope One LED light to go.

The Hope One is held to the quick release mount with a single M5 bolt and the mounting area on the light is flat which made it much easier to make a bracket to fit into the GoPro mount and then bolt onto the light unit.

Milling the 10mm material Using the edge finder Milling the 3mm slot

We designed the new mount in Adobe Illustrator (pdf download below) and after printing and cutting out different designs we found that a mount which holds the light approx. 35mm in front of the GoPro mount would give enough clearance for the brake and gear cables on the handlebars.

The mounting bracket for the GoPro cameras uses 3mm wide “fins” with a 5mm centre mounting hole.

The new bracket was milled from an offcut of 10mm aluminium with the GoPro bracket end being milled down to 9mm on one side. A 5mm hole was drilled to accept the GoPro securing bolt and then the outline was milled using a 4mm cutter.

The mount was then fitted in the mill vice and a 5mm hole was drilled for light bolt and this was countersunk using an 8.5mm end mill to 3.5mm to recess the mounting bolt. The slot for the GoPro mount was then milled using a 3mm end mill to a depth of 16mm.

We then test fitted the new bracket to the GoPro mount and found that the fit was slightly too tight and so we use 1000 grit wet/dry paper to make the centre slot slightly wider by approx. 0.1mm.

Checking the new bracket in the GoPro mount Light fitted to the bracket Mounted under the Garmin 810

I replaced the standard GoPro clamping bolt with a clamping handle from WDS Component Parts Ltd, part no: Clamping Handle Indexing with Stainless Steel Screw – Black Grey (8325-22225) and added a 10mm spacer to allow the clamping handle to clear the GoPro waterproof case. The new clamping handle has a quick turn handle which allows you to tighten the bolt and then pull the handle back slightly which releases the indexing and this lets you rotate the handle separately so it is facing back away from the front of the camera or light.

It also makes it much easier to securely clamp the GoPro camera or light when using gloves or with cold hands!

Top view of the mount and Garmin Front view Clamping Handle

Download the PDF plan for this mount.







 

More Articles to Read

Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown
Blinking Christmas Lights
Blinking Christmas Lights
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adding an “extra sense” with rangefinders
Adding an “extra sense” with rangefinders
This wireless game controller looks like a rug
This wireless game controller looks like a rug
How to run your ESP8266 for years on a battery
How to run your ESP8266 for years on a battery
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Making beats on a tiny Arduino DJ controller
Making beats on a tiny Arduino DJ controller
Qinsi-QS5100 Sn63Pb37 solder profile
Qinsi-QS5100 Sn63Pb37 solder profile
Water Detection System
Water Detection System
Professional Hi-Fi 15W Tube Amplifier circuit
Professional Hi-Fi 15W Tube Amplifier circuit
This Arduino machine will judge how sick your ollies are
This Arduino machine will judge how sick your ollies are
Turn an old payphone into a boombox for ’90s hits
Turn an old payphone into a boombox for ’90s hits
Big F’n 3D printer build
Big F’n 3D printer build
Temperature alarm for boiling milk
Temperature alarm for boiling milk
QuadBot is a 3D-printable walking robot for everyone
QuadBot is a 3D-printable walking robot for everyone
MicroConverter I2C Compatible Interface
MicroConverter I2C Compatible Interface

Top


Shares