Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Parallel Port Breakout board with Buffer for CNC & Routers

Parallel Port Breakout board with Buffer for CNC & Routers

Parallel port I/O break out board designed for Hobby CNC, Routers and Motion controller ,  This Board is an easy solution to driver stepper Motor driver, AC Servo (with Step-DIR Driver) and DC servo (with Step-DIR Driver), The Board is compatible with various CNC software specially made for LPT port data out. The board has been tested with MACH3 CNC software.   All outputs are buffered, all inputs are optical isolated and can be used as emergency switch, limit switch and home switch.

The board has 12 output pins that can control various devices such as stepping motor drivers, AC Servo Driver, DC Servo Driver,  Plasma Torch, Pump for coolant, spindle, 5 Input pins are provided for limit or home switches, feedbacks, Emergency switch.  All inputs has 470E for current controlled and TTL Voltage input required driving the inputs. This board can be powered with USB input or DC input supply 7V to 36V, keep jumper J2 open in case of USB supply input. Board has Screw Terminals for Inputs and out connections and also provided with 4X6Pin header connecters for outputs. J15 is connected directly to parallel port pins for testing purpose.

Note: For 24V input signal replace of R3, R4, R5, R6, and R7 with 2K2 Ohms.

Features

  • Supply 7V to 36V DC
  • 25 D SUB Female Connecter for PC LPT Port Interface
  • On Board Power LED
  • On Board USB Connector for Supply from PC or other USB source
  • Jumper Selection for USB Supply Input or External Supply
  • All Outputs are buffered
  • All inputs are optically isolated
  • Two Options for Outputs, Screw Terminals and Header Connectors
  • 4X6Pin Header for easy motor driver interface
  • On Board L317 Regulator for 5V DC
  • Heat sink for regulator
  • 5V DC Output for External Circuits
  • 3X3 Header Connector for Relay Driver for Spindle, Plasma, Laser, Pump ON/OFF

Parallel Port Breakout board with Buffer for CNC & Routers – [Link]

The post Parallel Port Breakout board with Buffer for CNC & Routers appeared first on Electronics-Lab.

Pinned onto

Related Pins

One Phase Power Meter
One Phase Power Meter
WiFi Toilet Vacancy Sensor
WiFi Toilet Vacancy Sensor
HAL 9000 reimagined as a useless machine
HAL 9000 reimagined as a useless machine
Using the XMEGA Clock System
Using the XMEGA Clock System
An Arduino VU meter for classrooms
An Arduino VU meter for classrooms
DIY Calculator
DIY Calculator
Build your own robotic vacuum from scratch
Build your own robotic vacuum from scratch
An animatronic talking takeout container
An animatronic talking takeout container
Restoring a Xerox Alto day 7: experiments with disk and Ethernet emulators
Restoring a Xerox Alto day 7: experiments with disk and Ethernet emulators
IDE 1.6.12 released with Sierra support and more
IDE 1.6.12 released with Sierra support and more
IoT Propane Tank
IoT Propane Tank
Industry Standard Single-Ended Current Mode PWM Controller
Industry Standard Single-Ended Current Mode PWM Controller
Wifi enabled 8×64  pixel  LED  matrix display
Wifi enabled 8×64 pixel LED matrix display
Arduino Disco Lights
Arduino Disco Lights
PIXIE is an Arduino-based NeoPixel watch
PIXIE is an Arduino-based NeoPixel watch
How to run C programs on the BeagleBone’s PRU microcontroller
How to run C programs on the BeagleBone’s PRU microcontroller
Capture time-lapses with a steel and aluminum camera slider
Capture time-lapses with a steel and aluminum camera slider
The MR-808 is a robotic drum “synthesizer”
The MR-808 is a robotic drum “synthesizer”
HDMI 2.0 Implementation on Kintex-7 FPGA GTX Transceivers
HDMI 2.0 Implementation on Kintex-7 FPGA GTX Transceivers
Meet Floris.cc: a new Genuino reseller in The Netherlands
Meet Floris.cc: a new Genuino reseller in The Netherlands

Top


Shares