Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Quicksilver G4 Overclocking and Voltage Tweak

Quicksilver G4 Overclocking and Voltage Tweak

how to overclock the Quicksilver Power Mac
This mod was fond at http://thomas.perrier.name/otherStuff/quicksilverg4ove.html. If you are looking to overclock that Quicksilver or change the voltage to handle another mod or even this one, check out this guide.

The main mod, the one which is the source of the need for the other ones!

The Mystic Room was the first site to show how to overclock the Quicksilver Power Mac. Since I wanted to be able to easily switch between multipliers, I used a DIP switch mounted on a small board with 1 kÙ resistors (same value as the resistors unsoldered from the CPU daughter card). Very useful, and raises the coolness factor tremendously :]

The rubber band and tape are there to hold the wires, since if they move close to the solders these can break very easily. Thankfully the picture is a little blurry, so my poor work with the voltage registers isn’t too apparent :] These resistors sure are tiny…

While overclocking to 933 MHz was a walk in the park, at 1 GHz an annoying issue appeared: L3 cache was usually not activated at startup, either silently with OS X, or with an alert box with OS 9. At first I suspected the L3 cache chips, but then saw that they were rated for 250 MHz, so that probably wasn’t the source of the problem. (These chips are DDR memory, so effective maximum clock rate is 500 MHz; as the 7450 in the Power Mac G4 867 drives the L3 cache at half the processor clock rate, up to 1 GHz the L3 cache isn’t overclocked).

I then considered raising the 7450’s core voltage. Inspired by Michiro Isobe’s article on Digital Audio Power Macs overclock, I examined the Quicksilver CPU daughter card, found the buck controller (ON Semi CS5165), read its documentation, and obtained the following table:

Visit Here for more.







 

More Articles to Read

Serial seven segment LED display shield
Serial seven segment LED display shield
Serial seven segment LED display shield
Serial seven segment LED display shield
G-code controlled drawing plotter
G-code controlled drawing plotter
An Arduino round word clock
An Arduino round word clock
The Sandwich-o-Matic will make your lunch automatically
The Sandwich-o-Matic will make your lunch automatically
Scalar Network Analyser Jr
Scalar Network Analyser Jr
An Arduino-controlled automated whiskey distillery
An Arduino-controlled automated whiskey distillery
The Rex800 looks like a dinosaur Terminator
The Rex800 looks like a dinosaur Terminator
Home Environment Monitor
Home Environment Monitor
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
Noisy ESP8266
Noisy ESP8266
Noisy ESP8266
Noisy ESP8266
App note: Noise analysis for high-speed op amps
App note: Noise analysis for high-speed op amps
Skill Sunday: Arrays
Skill Sunday: Arrays
App note: Infrared remote control implementation with MSP430FR4xx
App note: Infrared remote control implementation with MSP430FR4xx
Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown

Top


Shares