Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Guitar Reverb Effect Version 2

Guitar Reverb Effect Version 2

This second-generation guitar reverb circuit features clipping indicators on the preamp and reverb recovery stages, allowing for the optimal gain settings. The fidelity is much improved over the earlier design, it is suitable for use as a front-end to a guitar amplifier.
The guitar input stage is a class A amplifier with adjustable bias. A 2N3906 PNP tranistor is used for a low noise design on this stage. The output of the preamp stage is sent to three places: the output mixer amp, the reverb driver amp, and the input clipping detector.

The reverb driver amp consists of a phase inverting push-pull circuit made from dual sections of a 5532 high quality audio op-amp. This provides a voltage swing of approximate twice the supply voltage to the reverb impedance matching transformer, allowing higher power transfer. The 100 ohm resistor is critical for insuring a clean drive signal, without it, the op-amps can saturate when driving the transformer, producing unwanted distortion.

The transformer matches the impedance of the driver amplifer to the reverb driver coil and allows a dual phase driving signal to power a reverb coil with one grounded side. The transformer is a standard “70 volt” audio line transformer that is often found on PA systems. If you can find a reverb tank with a high impedance driver coil, the transformer may be eliminated, the driver coil will require isolation from ground.

The output of the reverb tank is sent to the reverb recovery amp, it is also a 2N3906 class A low noise stage.

The mixer amplifier is a 2N3904 transistor biased for class A operation. It mixes the dry signal from the input preamplifer with the wet signal from the reverb recovery amp through two 10K resistors. The wet signal level is adjusted by a 10K potentiometer.

The clipping detector stages receive inputs from the guitar preamp and the reverb recovery amp, they act in an identical manner. The 1458 op-amp is wired as a comparator with a threshold that is near the high side of the allowable voltage swing on the associated 2N3906 preamp stage. If the transistor output exceeds this voltage, the 1458 output turns on, causing the 4011 one-shot pulse stretcher circuit to fire. The one-shot circuit activates the LED, and stays on long enough that even minor clipping on the amplifier causes visible blinking.

The power supply filter involves an RC filter between the DC input and the VF1 power bus. VF1 drives the reverb driver, the output amp, and the clipping circuit. VF2 and VF3 are further filtered with their own RC filters, they provide isolated DC for powering the input preamp and reverb recovery amplifier stages.

Visit Here for more.







 

More Articles to Read

Peeqo is a desktop bot that communicates through GIFs
Peeqo is a desktop bot that communicates through GIFs
Using a Programmable Input Multiplier to Minimize Integer Boundary Spurs
Using a Programmable Input Multiplier to Minimize Integer Boundary Spurs
Serial seven segment LED display shield
Serial seven segment LED display shield
G-code controlled drawing plotter
G-code controlled drawing plotter
An Arduino round word clock
An Arduino round word clock
The Sandwich-o-Matic will make your lunch automatically
The Sandwich-o-Matic will make your lunch automatically
Scalar Network Analyser Jr
Scalar Network Analyser Jr
An Arduino-controlled automated whiskey distillery
An Arduino-controlled automated whiskey distillery
The Rex800 looks like a dinosaur Terminator
The Rex800 looks like a dinosaur Terminator
Home Environment Monitor
Home Environment Monitor
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
Noisy ESP8266
Noisy ESP8266
App note: Noise analysis for high-speed op amps
App note: Noise analysis for high-speed op amps
Skill Sunday: Arrays
Skill Sunday: Arrays
App note: Infrared remote control implementation with MSP430FR4xx
App note: Infrared remote control implementation with MSP430FR4xx
Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown

Top


Shares