Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Two line intercom plus a telephone changeover switch

Two line intercom plus a telephone changeover switch

The circuit presented here can be used for connecting two telephones in parallel and also as a 2-line intercom. Usually a single telephone is connected to a telephone line.
If another telephone is required at some distance, a parallel line is taken for connecting the other telephone. In this simple parallel line operation, the main problem is loss of privacy besides interference from the other phone. This problem is obviated in the circuit presented here.

Under normal condition, two telephones (telephone 1 and 2) can be used as intercom while telephone 3 is connected to the lines from exchange. In changeover mode, exchange line is disconnected from telephone 3 and gets connected to telephone 2. For operation in intercom mode, one has to just lift the handset of phone 1 and then press switch S1. As a result, buzzer PZ2 sounds. Simultaneously, the side tone is heard in the speaker of handset of phone 1. The person at phone 2 could then lift the handset and start conversation. Similar procedure is to be followed for initiation of the conversation from phone 2 using switch S2. In this mode of operation, a 3-pole, 2-way slide-switch S3 is to be used as shown in the figure.

In the changeover mode of operation, switch S3 is used to changeover the telephone line for use by telephone 2. The switch is normally in the intercom mode and telephone 3 is connected to the exchange line. Before changing over the exchange line to telephone 2, the person at telephone 1 may inform the person at telephone 2 (in the intercom mode) that he is going to changeover the line for use by him (the person at telephone 2). As soon as changeover switch S3 is flipped to the other position, 12V supply is cut off and telephones 1 and 3 do not get any voltage or ring via the ring-tone-sensing unit.

Once switch S3 is flipped over for use of exchange line by the person at telephone 2, and the same (switch S3) is not flipped back to normal position after a telephone call is over, the next telephone call via exchange lines will go to telephone 2 only and the ring-tone-sensing circuit will still work. This enables the person at phone 3 to know that a call has gone through. If the handset of telephone 3 is lifted, it is found to be dead. To make telephone 3 again active, switch S3 should be changed over to its normal position.

Visit Here for more.







 

More Articles to Read

App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: Noise analysis for high-speed op amps
App note: Noise analysis for high-speed op amps
Skill Sunday: Arrays
Skill Sunday: Arrays
App note: Infrared remote control implementation with MSP430FR4xx
App note: Infrared remote control implementation with MSP430FR4xx
Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown
Blinking Christmas Lights
Blinking Christmas Lights
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adding an “extra sense” with rangefinders
Adding an “extra sense” with rangefinders
This wireless game controller looks like a rug
This wireless game controller looks like a rug
How to run your ESP8266 for years on a battery
How to run your ESP8266 for years on a battery
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Making beats on a tiny Arduino DJ controller
Making beats on a tiny Arduino DJ controller
Qinsi-QS5100 Sn63Pb37 solder profile
Qinsi-QS5100 Sn63Pb37 solder profile
Water Detection System
Water Detection System
Professional Hi-Fi 15W Tube Amplifier circuit
Professional Hi-Fi 15W Tube Amplifier circuit
This Arduino machine will judge how sick your ollies are
This Arduino machine will judge how sick your ollies are
Turn an old payphone into a boombox for ’90s hits
Turn an old payphone into a boombox for ’90s hits

Top


Shares