Organize and Share your Electronics the way you want. Sign-Up for a free account now. It takes only 30 seconds!

Lightning Activated Camera Shutter Trigger

Lightning Activated Camera Shutter Trigger

This circuit is used to trigger a camera’s electronic shutter circuit when a flash of lightning is present. This circuit would also work for photographing fireworks displays or other events involving flashes of light.
The circuit can be built on a small piece of perforated circuit board using a point-to-point wiring technique. The circuit board can be mounted inside of a small plastic case, preferably made of black plastic. The photodarlington transistor can be mounted in a hole on the side of the box, a small metal clip can be used to slide over the camera’s viewfinder. Unfortunatly, there is no standard for viewfinder mounts between camera manufacturers.

When shooting through an SLR camera, this circuit should only be used at night. Daytime use will cause it to retrigger indefinitely because the SLR’s viewfinder goes black then bright when the photo is done, this restarts the detector.

For daytime use, it may be preferable to mount the photodarlington transistor in a black tube, the tube should be cut to a length that gives the transistor an angle of view that is similar to the camera lens setting. The back of the tube should be covered with something black to block light from the back side.

The camera should always be set up on a tripod, the lightning trigger should be physically secured to the camera. Slower film speeds will improve the ability to capture lightning photos. I have had good luck with ASA 100 and 200 film, both color and black and white.

The camera setting depends on the model used, I have taken many good shots with a Nikon N2000 camera in auto-exposure mode. A newer Nikon N70 responds too slowly in auto-exposure mode, try using a manual exposure mode with a tight F setting and a long time duration. A digital camera would be ideal, due to the “free film”. Unfortunately, very few digital cameras have external trigger inputs, and many suffer from a very long delay from shutter press until the photo is taken. The use of manual exposure settings may improve the speed of the camera.

When dealing with large thunderstorms, lightning strikes often create a conductive path, then strike multiple times through the same path. This type of strike is the easiest to photograph. The most difficult strikes to catch are single zaps in the daytime. Daylight photos require short exposure times, lowering the chances of a zap being caught on film.

When using this circuit, be prepared to run through a lot of film, a good storm can empty a 36 exposure roll in just a few minutes. Typically, around half of those shots will be good when taking nighttime photos. Different storms have different “personalities”, some will produce a lot of quick zaps, while others will light the sky up in an almost continuous manner.

When using the circuit, be sure to stay away from sources of flickering light such as street lights and fluorescent lights, they will cause false triggering. It is normal for the circuit to activate constantly when in the presence of indoor lights. I recommend testing the circuit by shining a flash light across the detector in a completely dark room.

Visit Here for more.







 

More Articles to Read

Scalar Network Analyser Jr
Scalar Network Analyser Jr
An Arduino-controlled automated whiskey distillery
An Arduino-controlled automated whiskey distillery
The Rex800 looks like a dinosaur Terminator
The Rex800 looks like a dinosaur Terminator
Home Environment Monitor
Home Environment Monitor
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
Understanding the Operation of the Frequency Synthesizer in Maxim’s RF Transceivers
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: EPIC: Electro-Pyrotechnic Initiator Chip Resistor
App note: Noise analysis for high-speed op amps
App note: Noise analysis for high-speed op amps
Skill Sunday: Arrays
Skill Sunday: Arrays
App note: Infrared remote control implementation with MSP430FR4xx
App note: Infrared remote control implementation with MSP430FR4xx
Gesture Controlled Smart Home
Gesture Controlled Smart Home
Design for a Wideband, Differential Transimpedance DAC Output
Design for a Wideband, Differential Transimpedance DAC Output
Wrist thrusters let you fly through the water effortlessly
Wrist thrusters let you fly through the water effortlessly
Bertan/Spellman 225-20R HV power supply teardown
Bertan/Spellman 225-20R HV power supply teardown
Blinking Christmas Lights
Blinking Christmas Lights
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adjusting clock with alarm, hygrometer & thermometer on 1.8″ ST7735 display
Adding an “extra sense” with rangefinders
Adding an “extra sense” with rangefinders
This wireless game controller looks like a rug
This wireless game controller looks like a rug
How to run your ESP8266 for years on a battery
How to run your ESP8266 for years on a battery
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Calibration of a 3-Phase Energy Meter Board on the ADE7754
Making beats on a tiny Arduino DJ controller
Making beats on a tiny Arduino DJ controller

Top


Shares