Parts

2N3055 and MJ2955: pinout, ratings, base drive, heatsink and the PNP partner

By

The 2N3055 has only two pins: pin 1 is the base and pin 2 is the emitter. The metal can is the collector. Seen from below with the pins toward you, both pins sit closer to one mounting hole, one each side of the line between the holes. The PNP partner, the MJ2955, uses the same can and the same pins.

It is a 60 V, 15 A NPN power transistor in the TO-3 (TO-204AA) package, rated 115 W with the case held at 25 °C. onsemi gives no free-air rating at all, so plan on a heatsink every time. The gain is low: at least 20 at 4 A and only 5 at 10 A, which is why the base needs hundreds of milliamps. Every figure on this page comes from onsemi's datasheet.

Datasheet: onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D) (PDF)

Advertisement

Pinout by package

2N3055G TO-3 · onsemi1=B 2=E
E2 EmitterB1 Basecase = collectorbottom view, pins toward you

Bottom view, pins toward you: both pins sit nearer one mounting hole, one each side of the line between the holes. The metal case is the collector.

Source: onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D), p. 4 (TO-204 (TO-3) Case 1-07 Style 1: pin 1 base, pin 2 emitter, case collector; bottom-view outline with pins 1 and 2); onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D), p. 1 (marking diagram xxxx55G (2N30 or MJ20), ordering table 2N3055G)

MJ2955G TO-3 · onsemi1=B 2=E
E2 EmitterB1 Basecase = collectorbottom view, pins toward you

The same can and pins as the 2N3055: pin 1 base, pin 2 emitter, case collector.

Source: onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D), p. 4 (same Case 1-07 Style 1 outline for both devices)

Which one do you have?

  • onsemi marks the can 2N3055G (the G means lead-free) with a location code, a year and work week, and the country of origin. The MJ2955 carries MJ2955G.
  • Both come only in the TO-3 metal can on this sheet. A plastic part sold as a "2N3055" in a different package is not covered by these figures.
  • We fetched no second maker's 2N3055 sheet for this page, so it uses onsemi's figures only. Check the sheet of the part you buy.

Ratings and characteristics

Limits from onsemi 2N3055/D (2N3055G and MJ2955G)
Parameter2N3055GTO-3MJ2955GTO-3
PolarityNPNPNP
Collector-emitter voltage VCEO60 V−60 V
Collector-emitter voltage, 100 Ω base-emitter VCER70 V−70 V
Collector-base voltage VCB100 V−100 V
Emitter-base voltage VEB7 V−7 V
Collector current, continuous IC15 A−15 A
Base current IB7 A−7 A
Power, case held at 25 °C PD115 W (derate 0.657 W/°C)115 W
Thermal resistance, junction to case RθJC1.52 °C/W maxsame
Thermal resistance, junction to air RθJAnot givennot given
Junction temperature TJ−65 to 200 °C−65 to 200 °C
Electrical characteristics at a case temperature of 25 °C
Parameter2N3055GTO-3MJ2955GTO-3
Collector-emitter sustaining voltage VCEO(sus)IC = 200 mA, IB = 060 V min60 V min
Collector cut-off current ICEOVCE = 30 V, IB = 00.7 mA max0.7 mA max
DC current gain hFEIC = 4 A, VCE = 4 V20 to 7020 to 70
DC current gain hFEIC = 10 A, VCE = 4 V5 min5 min
Saturation voltage VCE(sat)IC = 4 A, IB = 400 mA1.1 V max1.1 V max
Saturation voltage VCE(sat)IC = 10 A, IB = 3.3 A3 V max3 V max
Base-emitter on voltage VBE(on)IC = 4 A, VCE = 4 V1.5 V max1.5 V max
Second breakdown current Is/bVCE = 40 V, t = 1 s2.87 A min2.87 A min
Gain-bandwidth product fTIC = 0.5 A, VCE = 10 V2.5 MHz min2.5 MHz min
  • The 115 W figure holds only while the case stays at 25 °C. It falls by 0.657 W for every degree above that and reaches zero at 200 °C, which is the same as the 1.52 °C/W junction-to-case figure.
  • At high voltage the limit is second breakdown, not heat. onsemi guarantees 2.87 A for 1 s at 40 V across the transistor, about 115 W.
  • The gain is given at 4 A and 10 A only. This page designs to the 4 A floor of 20.
0204060at 4 A20 to 70at 10 A5 minimum
Figure 1. DC current gain at VCE 4 V. At 4 A the bar runs to the 70 maximum and the black tick marks the 20 minimum; at 10 A onsemi gives only the minimum, 5. Design to the minimum.

What it is good for

Linear power supplies (the pass transistor after a zener or regulator), audio output stages with the MJ2955 on the other side, and switching heavy DC loads such as motors, heaters and lamps at a few amps. For fast switching it is a poor fit: its gain-bandwidth product is only 2.5 MHz, and a logic-level MOSFET switches the same current with far less drive.

Switching 4 A: what the base needs

A microcontroller pin gives about 20 mA. At the gain floor of 20, that holds 400 mA of collector current at the very most, and the transistor is not saturated there. Take a 3 Ω load on 12 V instead, 4 A when fully on.

  • onsemi specifies the 1.1 V saturation limit at 4 A with 400 mA of base current, a forced gain of 10. Use that as the target.
  • From a 5 V drive and the 1.5 V VBE(on) maximum: (5 − 1.5) ÷ 0.4 A = 8.75 Ω, so use 8.2 Ω.
  • Base current then runs from 427 mA (VBE 1.5 V) to 537 mA (VBE 0.6 V). The resistor itself burns up to 2.4 W, so use a 5 W part.
  • The load gets at least (12 − 1.1) ÷ 3 = 3.63 A.
R1 8.2 Ω Q1 2N3055 R2 load 3 Ω +12 V 5 V drive
Figure 2. The switch as built: 8.2 Ω from a 5 V drive to the base, a 3 Ω load from 12 V. Simulated with a model whose gain is set to onsemi's minimum of 20: 488 mA of base current, 3.86 A through the load, 0.43 V left across the transistor.

Half an amp of base drive has to come from somewhere. A small transistor such as a BD139 or a TIP31C between the pin and the 2N3055 does it (the pair then works as a Darlington), or a logic-level MOSFET replaces the whole stage (see IRFZ44N vs IRLZ44N).

0200 mA400 mApin, 20 mA4 A, hFE 20200 mA minimum4 A, sat. test400 mA for 1.1 V8.2 Ω drive427 mA to 537 mA
Figure 3. Base current against the 20 mA a microcontroller pin is specified for. Even onsemi's 4 A saturation test asks for 400 mA, twenty times the pin.

Heatsink sums

Fully on at 4 A, the 2N3055 makes up to 1.1 × 4 = 4.4 W. With no free-air figure on the sheet, it goes on a heatsink. Keeping the junction at 150 °C (our margin under the 200 °C maximum) in 40 °C air, the heatsink and pad may total (150 − 40) ÷ 4.4 − 1.52 = 23.5 °C/W. Check the heatsink maker's rating against that.

As a linear pass element it works much harder. Say it drops 24 V to 12 V at 3 A in 40 °C air:

  • Heat: (24 − 12) × 3 = 36 W.
  • The whole path from junction to air may total (150 − 40) ÷ 36 = 3.06 °C/W. The junction-to-case part takes 1.52 °C/W, which leaves 1.54 °C/W for the pad and the heatsink together. That is a large finned sink.
  • The case then sits near 95 °C, too hot to touch.
  • The base needs 3 ÷ 20 = 150 mA at the gain floor, so the reference that drives it needs a driver transistor too.
0 °C100 °C200 °C150 °C target200 °C max0.5 °C/W sink113 °C1.5 °C/W sink149 °C2.5 °C/W sink185 °C
Figure 4. Junction temperature for the 36 W pass element in 40 °C air, by heatsink plus pad rating. 1.5 °C/W keeps it near our 150 °C target; 2.5 °C/W runs close to the 200 °C maximum.
050 W100 Wcase 25 °C115 Wcase 50 °C98.6 Wcase 75 °C82.2 Wcase 100 °C65.7 Wcase 125 °C49.3 Wcase 150 °C32.9 Wcase 175 °C16.4 W
Figure 5. The 115 W rating against case temperature: it falls by 0.657 W per °C above 25 °C. A case at 100 °C allows about 66 W.

MJ2955 and the push-pull pair

The MJ2955 is the PNP mirror on the same onsemi sheet: −60 V, −15 A, the same 115 W and 1.52 °C/W, the same gain and saturation limits, and the same can with pin 1 base and pin 2 emitter. A 2N3055 on one side and an MJ2955 on the other make a push-pull output stage. On a split supply the off transistor sees both rails added together, so keep the total under 60 V, and check the second-breakdown limit of 2.87 A at 40 V before driving a low-impedance load.

Worked example in numbers

Pins
1 B, 2 E, case C
Base current for 4 A
400 mA
Base resistor from 5 V
8.2 Ω
Sink + pad, 36 W at 40 °C
≤ 1.5 °C/W

Substitutes

TO-3: bottom view, pins toward you, as onsemi draws Case 1-07.
PartPinsVerdict
MJ2955 (PNP partner)pin 1 B, pin 2 E, case CThe PNP complement on the same sheet, for the high side of a push-pull pair or a PNP pass element. Same can, pins and limits with the polarity reversed.onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D), p. 1
TIP31C (TO-220)B-C-ENot a replacement for high-current work: 3 A and 40 W against 15 A and 115 W. It fits only where the load stays well under 3 A, and the pins and package differ.onsemi Complementary Silicon Power Transistors 2N3055 (NPN), MJ2955 (PNP) (2N3055/D), p. 1
Advertisement

Tips and checks

  • Use thermal grease or a silicone pad under the can. The 1.52 °C/W figure stops at the case; a dry joint adds to it.
  • Fit a flyback diode across a motor or relay coil. The sheet gives no avalanche rating, so the switch-off kick has nowhere safe to go.
  • Put a resistor of about 100 Ω from base to emitter. onsemi rates VCER, the collector-emitter limit with 100 Ω there, at 70 V against 60 V with the base open, and it keeps the transistor off when the drive floats.
  • The case is live. Solder or crimp the collector wire to a lug under one mounting screw, and keep the can away from other metal.
  • Size the base drive for the gain floor, not the gain your meter shows on one sample. The sheet allows 20 to 70 at 4 A.

Testing one with a meter

Set the meter to diode test. On a 2N3055, red on pin 1 (base) and black on pin 2 (emitter) reads a junction; so does red on pin 1 and black on the can. Every other pair reads open, including pin 2 to the can in either direction. On an MJ2955 the probes swap: black on the base. A reading between emitter and case means the transistor is shorted.

What we'd do

We'd use the 2N3055 where its size pays: linear supplies and audio stages that dissipate tens of watts, on a proper heatsink sized with the sum above, driven by a BD139 or TIP31C. For simple on-off switching of a few amps from a microcontroller, we'd pick a logic-level MOSFET instead, which needs almost no drive current and wastes less heat.

Questions people ask

Where is the collector on a 2N3055?

The collector is the metal can. Pin 1 is the base and pin 2 is the emitter. The mounting screws touch the can, so they are the collector too.

Can an Arduino drive a 2N3055 directly?

Not usefully. A pin gives about 20 mA, enough for about 400 mA at the gain floor. Put a BD139 or TIP31C in front, or use a logic-level MOSFET.

Does a 2N3055 need a heatsink?

Yes. onsemi gives it no free-air rating. Even fully on at 4 A it makes up to 4.4 W.

What is the PNP version of the 2N3055?

The MJ2955, on the same onsemi datasheet, with the same can, pins and limits.

Is it really 115 W?

Only with the case held at 25 °C. With a real heatsink in warm air the case runs much hotter; at a case of 100 °C the limit is about 66 W.

Buying the 2N3055 in India

The TO-3 2N3055 and MJ2955 are still sold by Indian component shops. Look for the maker's marking on the can, and test each one with a meter before fitting it. Our guide to buying electronic components in India compares ten online sellers and covers how to spot fakes.

Where to go next

The BJT as a switch lesson works through base resistors from the start, transistor packages and heat covers the heatsink sum, and the push-pull output stage explains the complementary pair. For a smaller part in a TO-220, see the TIP31C.

Advertisement

One email a month from the bench

New circuits, lessons, part guides and calculators, on the first Sunday of each month.

We'll send one email to confirm. Every email has a one-click unsubscribe. Privacy policy

Used in these lessons

Lessons that go deeper

Datasheets this page was checked against

Makers revise datasheets. If the copy you download has a newer revision and a number here disagrees with it, the datasheet wins, and we would like to hear about it.