Will It Work? · Checker

Will this Ethernet cable reach full speed?

By , founder of ElectronicsInfoline (since 2000)

A wired link runs at the speed both ports share, if the cable can carry it. Pick each port's top speed and the category printed on the cable, type the length, and see what the link can reach. Add your internet plan to see whether the cable is what holds it back. The figures come from maker support pages and cabling notes, all quoted below.

The slower port sets the top speed. Then the cable: Cat5e carries up to 2.5 Gbps over 100 m, Cat6 up to 5 Gbps over 100 m and 10 Gbps up to 37 m (to 55 m it depends), and Cat6A or later carries 10 Gbps over the full 100 m. Plain Cat5 is listed for 100 Mbps.

1. The two ports

Router, switch, modem or fibre box: from its label or spec page.

Computer, console, TV or adapter: from its spec page.

2. The cable between them

Look along the cable for a word such as CAT6.

m

The whole run, wall cabling and patch cords together.

3. Your internet plan (optional)

Mbps

From your bill or the provider’s plan page.

YesRuns at 1 Gbps, the top speed of the slower port

Cat5e carries 1 Gbps up to 100 m.

Show the working
  1. Ports: 2.5 Gbps and 1 Gbps. The link can run at most the slower one: 1 Gbps.
  2. Cable: Cat5e, 10 m, at 1 Gbps: Cat5e carries 1 Gbps up to 100 m.
Two ports of 2.5 Gbps and 1 Gbps on 10 m of Cat5ePort A runs up to 2.5 Gbps, port B up to 1 Gbps, so the link can reach 1 Gbps at most. The cable is Cat5e, 10 metres. At 1 Gbps the answer is yes. Speed this cable surely carries here: 1 Gbps.A: 2.5 GbpsB: 1 GbpsCat5e · 10 mAt 1 Gbps: yesSurely carries: 1 Gbps
The slower port sets the top speed; the cable's category and length decide whether the link gets there. Green: yes. Amber: with limits. Red: no.

Speeds are link rates for copper cables with RJ45 plugs. The checker assumes each port also runs the slower speeds below its top one; the port's spec page has its full list. Nothing here is measured.

How two ports settle on a speed

Each port offers the speeds it runs, and the link takes the fastest one both have. Apple puts it this way: depending on the device at the other end, the cable type and its length, the highest link speed is negotiated automatically (Apple). Its own 10 Gbps port also runs the slower rates (Apple).

How two Ethernet ports agree on a speedPort A offers 100 Mbps, 1, 2.5, 5 and 10 Gbps. Port B offers 100 Mbps, 1 and 2.5 Gbps. The fastest speed on both lists is 2.5 Gbps, highlighted, and that is the most the link can run, if the cable carries it.Port A100M1G2.5G5G10GPort B100M1G2.5G5G10Glink: up to 2.5 GbpsGrey dashed: a speed that port does not run.
Figure 1. Each port offers the speeds it runs; the link settles on the fastest one both share, here 2.5 Gbps, provided the cable can carry it.

So a 10 Gbps computer on a 1 Gbps router port gets 1 Gbps at most, whatever the cable. The cable starts to matter once both ports run a high speed.

What each cable category carries

Apple's table gives the speeds per category for runs up to 100 m: Cat5e up to 5 Gbps and not 10 Gbps, Cat6 up to 10 Gbps but only to 55 m at that speed, Cat6a or later every speed to 10 Gbps (Apple). TP-Link's table lists plain Cat5 for 100 Mbps and Cat7 for 10 Gbps over 100 m (TP-Link).

Which Ethernet speeds each cable category carries, up to 100 mA grid. Cat5: 100 Mbps only. Cat5e: 100 Mbps, 1 and 2.5 Gbps yes; 5 Gbps with limits; 10 Gbps no. Cat6: up to 5 Gbps yes; 10 Gbps up to 37 metres yes and 37 to 55 metres with limits. Cat6A or later: every speed up to 10 Gbps.100M1G2.5G5G10Gcable \ speedCat5✓✗✗✗✗Cat5e✓✓✓~✗Cat6✓✓✓✓≤37 m ✓≤55 m ~Cat6A or later✓✓✓✓✓Not marked: no speed is certified. Past 100 m: no source gives a speed.
Figure 2. Up to 100 m, from the maker tables and the TSB-155 and 802.3bz notes cited below. ✓ yes, ~ with limits, ✗ no. Cat6 at 10 Gbps depends on length.

The sources differ on the faster rates. IEEE 802.3bz, as Fluke Networks sums it up, specifies 2.5 Gbps over 100 m of Cat5e and 5 Gbps over 100 m of Cat6, with 5 Gbps on Cat5e only in defined use cases (Fluke Networks). TP-Link recommends Cat5e or higher up to 2.5G, a shielded Cat5e or Cat6 for 5G, and a shielded Cat6A or better for 10G (TP-Link). That is why the checker gives Cat5e at 5 Gbps as “with limits” rather than a plain yes.

Cat6 at 10 Gbps: length decides

The TIA bulletin TSB-155, quoted by Fluke Networks, says 10GBASE-T should work over up to 37 m of Cat6, and between 37 and 55 m depending on the crosstalk from nearby cables; beyond 55 m it may need fixes (Fluke Networks). For a new run that must carry 10 Gbps over 100 m, the same page points to Cat6A (Fluke Networks).

Run length for 10 Gbps on Cat6 and on Cat6AA scale from 0 to 100 metres. Cat6 at 10 Gbps: green up to 37 metres, amber from 37 to 55 metres, red beyond 55 metres. Cat6A at 10 Gbps: green all the way to 100 metres.Cat6Cat6A0 m37 m55 m100 myesdependsnoBoth bars: 10 Gbps. Below 10 Gbps, Cat6 carries the full 100 m.
Figure 3. Cat6 runs 10 Gbps up to 37 m; from 37 to 55 m it depends on crosstalk from neighbouring cables; past 55 m it may need fixes. Cat6A is the category for 10 Gbps to 100 m.

Reading the cable and the ports

The checker needs three things you can read off the hardware: the category word on the cable jacket, and the top speed of each port from its label or the maker's spec page. A port listed as 10/100/1000 tops out at 1 Gbps; one listed as 2.5G or 10G says so.

Where to read the cable category and the port speedA length of network cable with an RJ45 plug at the left. Printed along the jacket: CAT6 U/UTP 4PR 23AWG. Below, a port with the label 10/100/1000, meaning it runs 10 Mbps, 100 Mbps and 1 Gbps; its top speed is 1 Gbps.plugCAT6U/UTP 4PR 23AWGCAT6category, printed along the jacket10/100/1000speeds in Mbps:top = 1 Gbps
Figure 4. The category word on the jacket (here CAT6) is what the checker asks for. A port's label or spec page lists its speeds; the last figure in a list like 10/100/1000 (Mbps) is its top speed.

Count the whole run: the cable in the wall plus the patch cords at both ends. If you can't find a category on the jacket, pick “nothing printed”. The checker then says no speed is certain.

Worked examples

Two 10 Gbps ports on 60 m of Cat6

Cat6 at 10 Gbps is listed up to 55 m only; this run is 60 m.

Result: no at 10 Gbps. The cable surely carries 5 Gbps at this length; for 10 Gbps over 60 m it takes Cat6A.

Two ports of 10 Gbps and 10 Gbps on 60 m of Cat6Port A runs up to 10 Gbps, port B up to 10 Gbps, so the link can reach 10 Gbps at most. The cable is Cat6, 60 metres. At 10 Gbps the answer is no. Speed this cable surely carries here: 5 Gbps.A: 10 GbpsB: 10 GbpsCat6 · 60 mAt 10 Gbps: noSurely carries: 5 Gbps
Figure 5. The slower port sets the top speed; the cable's category and length decide whether the link gets there. Green: yes. Amber: with limits. Red: no.

A 2.5 Gbps router port, a 2.5 Gbps computer, 20 m of Cat5e and a 1 Gbps plan

Cat5e carries 2.5 Gbps up to 100 m.

Plan: This wired link (2.5 Gbps) is faster than your plan (1000 Mbps), so it is not what limits your internet speed.

Result: yes. No new cable needed.

A 5 Gbps port and a 10 Gbps port on 15 m of Cat5e

Cat5e at 5 Gbps: Apple’s table ticks it, but the 802.3bz standard specifies 5 Gbps over Cat6 and over Cat5e only in defined use cases.

Result: with limits. The link tops out at 5 Gbps because of the slower port; the cable surely carries 2.5 Gbps, and Cat6 would make 5 Gbps certain.

Tips and tricks

  • Check the port speeds before buying a cable. If either port is 1 Gbps, any Cat5e or better cable already gives you everything that link can do.
  • Read the category off the cable jacket as well as the packet. The jacket is still there once the packet is gone.
  • Add the patch cords to the wall run when you measure. The length that counts is port to port.
  • For a 10 Gbps run longer than 37 m, skip Cat6 and lay Cat6A. Past 37 m, Cat6 at 10 Gbps depends on the cables around it.
  • If a 5 or 10 Gbps link keeps dropping, set the port to 2.5G or 1G by hand. TP-Link gives that as the fix when the cable can’t be changed.

What we would do

For a home with 1 Gbps or 2.5 Gbps ports, we would keep the Cat5e or Cat6 already in place; it carries those speeds over a full 100 m run. When both ends have 5 Gbps ports, we would use Cat6, the category 802.3bz specifies for 5 Gbps over the full run; TP-Link prefers a shielded one. For 10 Gbps, Cat6 is fine on short runs up to 37 m, and we would lay Cat6A for anything longer or for a new installation.

If the internet feels slow on a wired computer, find the slowest part first: the plan, then each port, then the cable. Wi-Fi has its own limits; for those, read Wi-Fi generations explained. For a USB Ethernet adapter on a laptop, the USB-C hub and dock checker covers the port it plugs into.

Questions people ask

Is Cat5e good enough for gigabit Ethernet? Yes. Cat5e carries 1 Gbps over the full 100 m, and 2.5 Gbps too. The IEEE 802.3bz standard specifies 2.5 Gbps over 100 m of Category 5e.

Can a Cat6 cable run 10 Gbps? Over a short run, yes. TSB-155 says 10GBASE-T should work up to 37 m of Cat6, and from 37 to 55 m it depends on crosstalk from neighbouring cables. Past 55 m it may need fixes. For 10 Gbps over the full 100 m, use Cat6A.

Do 2.5 Gbps ports need a Cat6 cable? No. Cat5e is enough for 2.5 Gbps. Apple’s port table ticks it, TP-Link recommends Cat5e or higher up to 2.5G, and 802.3bz specifies 2.5 Gbps on Cat5e.

Will a Cat6A or Cat8 cable make my internet faster? Only if the old cable was holding the link back. A link never runs faster than the slower of its two ports, and your plan speed caps what comes in from outside. Put both port speeds and your plan into the checker to see which one sets the limit.

Does Cat5e work at 5 Gbps? The sources disagree, so the checker says “with limits”. Apple’s table ticks 5 Gbps on Cat5e. Fluke’s summary of 802.3bz says the standard specifies 5 Gbps over Cat6, and over Cat5e only in defined use cases. TP-Link recommends a shielded cable for 5G.

My 5 or 10 Gbps link keeps dropping. What can I do? TP-Link lists frequent link flapping and packet loss as the signs of a cable that can’t keep up at 5G or 10G. Its fixes: change to a shielded Cat6A or better, or set the port to 2.5G or 1G by hand.

How long can an Ethernet cable be? Every cable table used here is for runs up to 100 m (328 ft), and Cat6 at 10 Gbps is shorter, as above. For a longer run none of the sources gives a speed, so the checker says so.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. Apple, Apple Support: About the 10 Gigabit Ethernet port on Mac (Mac User Guide): Speeds are for cables up to 100 meters (328 feet) in length, unless otherwise indicated. Cable type 10BaseT 100BaseT 1 Gbit/s 2.5 Gbit/s 5 Gbit/s 10 Gbit/s Category 5e Not supported ✓ ✓ ✓ ✓ Not supported Category 6 Not supported ✓ ✓ ✓ ✓ ✓ — up to 55 m length Category 6a or later Not supported ✓ ✓ ✓ ✓ ✓ support.apple.com/guide/mac-help/mchlcef4be50/mac
  2. Apple, Apple Support: About the 10 Gigabit Ethernet port on Mac (Mac User Guide): Depending on the device you’re connecting to, the cable type and technology used, and the cable length, the highest link speed is automatically negotiated. For example, if the device you’re connecting to is 10 Gbit/s-capable and the cable can support the speed, the two devices would negotiate the 10 Gbit/s speed. support.apple.com/guide/mac-help/mchlcef4be50/mac
  3. Apple, Apple Support: About the 10 Gigabit Ethernet port on Mac (Mac User Guide): The 10 Gigabit Ethernet (RJ-45) port is Nbase-T Ethernet technology that supports multiple data rates for speeds up to 10 Gbit/s over standard twisted pair copper cabling up to 100 meters (328 feet) in length. support.apple.com/guide/mac-help/mchlcef4be50/mac
  4. TP-Link, TP-Link Omada Support: How to Choose Ethernet Cables for More Stable PoE Power Supply (FAQ 117489): Category 5 (CAT5) 100Base-T networks /10Base-T networks 1–100 MHz 100 Mbps 100 m Category 5e (CAT5e) 1000Base-T networks 1–100 MHz 1000 Mbps 100 m Category 6 (CAT6) 1000Base-T networks 1–250 MHz 1000 Mbps / 10 Gbps 100 m (1 Gbps) / 37–55 m (10 Gbps) Category 6A (CAT6A) 10GBase-T networks 1–500 MHz 10 Gbps 100 m Category 7 (CAT7) 10GBase-T networks 1–600 MHz 10 Gbps 100 m support.omadanetworks.com/us/document/117489/
  5. TP-Link, TP-Link Omada Support: How to Choose Ethernet Cables for More Stable PoE Power Supply (FAQ 117489): 100M / 1G / 2.5G Recommended Cable: Cat5E or higher Notes: Cat5E is sufficient; pure copper core minimizes voltage drops. 5G Recommended Cable: Cat5E/Cat6 + Shielded (FTP/SFTP) Notes: Unshielded (UTP) is not recommended; shielding reduces high-frequency interference. 10G Recommended Cable: Cat6A or higher + Shielded (SFTP) Notes: Cat6A or above ensures stable 10G transmission; 23 AWG preferred. support.omadanetworks.com/us/document/117489/
  6. TP-Link, TP-Link Omada Support: How to Choose Ethernet Cables for More Stable PoE Power Supply (FAQ 117489): If you are currently using Cat5E, Cat6, or Cat6 UTP cables and experience the following issues at 5G or 10G speeds: Frequent link flapping (port up/down) Persistent packet loss Unstable PoE power or device reboots Recommended Solutions: Replace the cable : Upgrade to Cat6A or higher shielded cable (SFTP) . Downshift the link speed : If cable replacement is not feasible, manually set the switch or device port speed to 2.5G or 1G to maintain stable power and communication. support.omadanetworks.com/us/document/117489/
  7. Fluke Networks, Fluke Networks Knowledge Base: 10GBASE-T field testing requirements (2014-01-28): TSB-155 states: "10GBASE-T should operate over channel lengths of up to 37 meters of Category 6 cabling, and should operate over channel lengths between 37 and 55 meters of Category 6 cabling depending on the alien crosstalk environment. Channel lengths over 55 meters may require mitigation." flukenetworks.com/knowledge-base/applicationstandards-articl…
  8. Fluke Networks, Fluke Networks Knowledge Base: 10GBASE-T field testing requirements (2014-01-28): If you are specifying a new installation designed to support 10GBASE-T up to 100 m (328 ft), you should be looking to the Category 6A specification . flukenetworks.com/knowledge-base/applicationstandards-articl…
  9. Fluke Networks, Fluke Networks blog: Will My Existing Cable Plant Support 2.5/5GBASE-T? (17 Jan 2018): IEEE 802.3bz specifies 2.5 Gbps over 100 meters of Category 5e cabling or 5 Gbps over 100 meters of Category 6 cabling. It also includes support for 5 Gbps over Category 5e on defined use cases (extended frequencies). flukenetworks.com/blog/cabling-chronicles/will-my-existing-c…

Author: Bulan Sarkar · Report an error

The check runs in your browser; nothing you type is sent anywhere. Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.