Will It Work? · Guide

Router lights: what amber, blinking and off mean, and what to do

By , founder of ElectronicsInfoline (since 2000)

The lights on the front of a router often show which link has failed before you open the settings page. This guide reads them from one maker's light table, then gives the fixes two makers' support pages give for an Internet light that is amber or off and a power light that will not settle, in the order they give them.

A solid amber Internet light means the router sees the cable to the modem but has no working connection; an Internet light that is off means no cable is detected. Power-cycle in order: everything off for 2 minutes, the modem first, the router 5 minutes later. If that fails, plug a computer straight into the modem. No internet there means the provider or the modem, not the router.

What each light reports

On one maker's routers, the Power light is solid amber while the router starts and turns white or green when it is ready (NETGEAR). Blinking amber means a firmware update is running or the reset button was pressed, and blinking white means the firmware is corrupted (NETGEAR). The Internet light is off when no Ethernet cable runs to the modem, solid amber when the cable is detected, and white or green when the connection is ready (NETGEAR).

The Ethernet port lights show speed as well: white or green for a 1 Gbps link, amber for 100 or 10 Mbps (NETGEAR). An amber port light is not a fault on its own; if a device should link at gigabit, the Ethernet cable checker shows whether the cable or the port at the other end holds it back. Icons differ with the age and model of the router (NETGEAR), and other makers use other colours, so check your router's quick installation guide against this table.

What the lights on a router mean, on one maker's tablePower light: solid amber while starting up, blinking amber during a firmware update or after the reset button was pressed, blinking white when the firmware is corrupted. Internet light: off when no Ethernet cable runs to the modem, solid amber when the cable is seen but the connection is not ready, solid white or green when the internet is ready. Wi-Fi light: off when the radios are switched off. Ethernet port light: white or green for a 1 Gbps link, amber for a 100 or 10 Mbps link. Other makers' colours differ; check the quick installation guide.lightstate and what it meansPowersolid amber: starting upblinking amber: firmware update, or reset pressedblinking white: firmware corruptedInternetoff: no cable to the modemsolid amber: cable seen, connection not readywhite/green: internet readyWi-Fioff: radios switched offwhite/green: radios onEthernet portwhite/green: linked at 1 Gbpssolid amber: linked at 100 or 10 MbpsDashed ring = blinking. Colours differ by maker and model.
Figure 1. One maker's light table. Solid amber on the Internet light means the router sees the cable to the modem but has no working connection yet. On the Ethernet ports, amber only means a slower link.

Internet light amber or orange

Amber on the Internet light means the router has found the modem cable but is not online (NETGEAR). The same maker lists an amber Internet light among the problems a full power cycle can fix, and gives the order (NETGEAR):

  1. Turn off the router, the modem and every device on the network. If the modem has a backup battery, take it out.
  2. Wait 2 minutes, then turn the modem on first.
  3. Wait 5 minutes while the modem connects to your provider. It can take longer.
  4. Turn the router on, then the wired and wireless devices.
Power-cycle a home network in the right orderMinute 0: turn off the router, the modem and every device; take out a modem backup battery if it has one. Minute 2: turn the modem on first. Wait 5 minutes while it connects to the provider. From minute 7: turn the router on, then the devices. With a modem router (one box), turn it on at minute 2 and the devices after 5 minutes.2 min off5 min: modem connects0 min2 min7 minall off(battery out)modem onrouter on,then devices onEarliest times. Wait longer if the modem's lightshave not settled; its manual says what settled looks like.
Figure 2. One maker's order: everything off for 2 minutes, modem first, 5 minutes for it to reach the provider (it can take longer), then the router, then the devices. It lists an amber Internet light among the problems this can fix.

If the light stays amber, find out whether the router is involved at all: plug a computer straight into the modem. If the computer cannot get online, the problem is the modem or the provider, not the router (TP-Link). If the computer works and the router does not, check the router's internet connection type and any login your provider gave you in the router's setup page.

Internet light off

An Internet light that is off points to the cable between the router and the modem (NETGEAR). First make sure it is an RJ45 Ethernet cable and not an RJ11 phone cable (TP-Link), and that it sits firmly in the router's WAN port. Then the other maker gives three tests in order (TP-Link):

  1. Computer straight on the modem. No internet: the modem or the provider.
  2. Move the router's WAN cable into one of its own LAN ports. If the Ethernet and Internet lights both come on, the WAN port works; if both stay off, the cable or the WAN port may be faulty, so try another cable first.
  3. If the port works, open the router page and set the internet port speed to 100 Mbps full duplex, then see whether the Internet light comes on.
Internet light off: three tests in orderFirst check the cable is an RJ45 Ethernet cable, not an RJ11 phone cable. Test 1: plug a computer straight into the modem. No internet: check the provider or the modem. Internet works: test 2, move the router's WAN cable into one of its LAN ports. Ethernet and Internet lights stay off: replace the cable or have the WAN port checked. Both light: test 3, set the internet port to 100 Mbps full duplex, then check the Internet light.RJ45 Ethernet cable, not an RJ11 phone cable?1. Computer straight on the modem:internet?noprovider or modemnot the routeryes2. Router's WAN cable into a LAN port:Ethernet + Internet lights on?nocable or WAN porttry another cable firstyes3. Port speed 100 Mbps full duplexthen watch the Internet lightStill off after all three: contact the maker withthe modem model, provider name and the results.
Figure 3. One maker's order for an Internet light that stays off. The first test decides whether the router is involved at all: if a computer on the modem gets no internet, the router is not the problem.

Power light stays amber or blinks

If the Power light does not turn white or green, or blinks for a long time, one maker suggests these checks (NETGEAR): use the power adapter that came with the router, plug it into a wall socket rather than a surge protector, and unplug every Ethernet cable from the LAN ports to see whether it then starts normally. Reconnect them one at a time to find the one that causes it. A network loop (a cable that runs from the router back into the same network) is a common cause (NETGEAR).

Firmware can be corrupted by a failed update or a power cut during one (NETGEAR), which is why the firmware update guide says to keep the router powered until it finishes. Leave a factory reset until last: it deletes every setting, including the admin user name and password, the Wi-Fi name and the security settings (NETGEAR). Note your Wi-Fi name and password before you press the button, and see the admin password guide for logging in afterwards.

Restart on a schedule

Some routers can restart themselves at a set time. On one maker's 4G routers the setting is under Advanced > System Tools > Reboot: turn on Reboot Schedule, then set the time and the Auto Reboot Interval (TP-Link). It runs on the router's own clock, so set the system time correctly first (TP-Link). The maker lists it for Archer MR200 V3 V4 and Archer MR600 V1 on that page; look in your own router's user guide for the same menu.

Neither maker's pages we read claim that a regular restart makes a router faster or more stable. Treat a schedule as a convenience, and if the router only works after a restart, look at the lights and the firmware instead.

Tips and tricks

  • Read the Internet light first: off means the cable, amber means the connection.
  • Power-cycle in order: modem first, router after the modem has settled. Turning both on at once skips the wait.
  • Plug a computer straight into the modem before you blame the router.
  • Amber on an Ethernet port light is a slower link, not a fault.
  • Never unplug a router while its power light shows a firmware update.
  • Save your Wi-Fi name and password before a factory reset; it deletes them.

What we would do

With an amber or dark Internet light, we would check the cable, power-cycle the modem and router in order, and then test a computer on the modem. That one test splits a provider problem from a router problem. We would leave the factory reset until the end, with the Wi-Fi details written down first.

Questions people ask

What does an amber or orange Internet light on my router mean? On one maker’s routers, solid amber means the router has found the Ethernet cable to the modem but has no working internet connection yet. Power-cycle the network in order (everything off for 2 minutes, modem first, router after 5 minutes). If it stays amber, plug a computer straight into the modem: no internet there means the provider or the modem, not the router.

Why is the Internet light on my router off? On one maker’s table it means no Ethernet cable runs between the router and the modem. Check the cable is an RJ45 Ethernet cable, not an RJ11 phone cable, and that it sits firmly in the WAN port. Then work through the three tests in this guide: computer on the modem, WAN cable moved to a LAN port, and the port speed set to 100 Mbps full duplex.

What does a blinking power light mean? On one maker’s routers, blinking amber means a firmware update is running or the reset button was pressed, and blinking white means the firmware is corrupted. Do not unplug a router during an update. A power light that stays amber or keeps blinking points to the power adapter, a LAN cable or loop, or the firmware.

Is it bad if an Ethernet port light is amber? No. On one maker’s routers the port light colour shows the link speed: white or green for 1 Gbps, amber for 100 or 10 Mbps. Amber on a gigabit port usually points to the cable or the device at the other end; the Ethernet cable checker on this site works out which.

Should I restart my router on a schedule? Some routers have a reboot schedule; on one maker’s 4G routers it is under Advanced > System Tools > Reboot and runs on the router’s own clock, so set the time first. The makers’ pages we read do not say a scheduled restart makes a router faster or more reliable, so treat it as a convenience.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. NETGEAR, NETGEAR KB 24244: what the LEDs on a router mean: Solid amber: Your router is powering on. Blinking amber: Your router’s firmware is upgrading or the Reset button was pressed. Blinking white: Your router’s firmware is corrupted. … Internet LED Off: No Ethernet cable is connected between the router and the modem. Solid green or white: The Internet connection is ready. Solid amber: The router detected an Ethernet cable connection to the modem. … WiFi LED Off: WiFi radios are off. … white or green for Gigabit Ethernet (1 Gbps) connections, and amber for 100 Mbps or 10 Mbps Ethernet connections. … Depending on the age and model of your NETGEAR router, the icons used for each LED may vary slightly kb.netgear.com/24244/
  2. NETGEAR, NETGEAR KB 19755: power cycling a home network: Your router's Internet LED light is amber. … If your modem has one, you must remove the backup battery to completely turn off your modem. Wait 2 minutes before turning on your cable or DSL modem again. … turn on your modem first and let it boot up. Wait 5 minutes while your modem establishes a connection with your Internet Service Provider (ISP). … After your cable or DSL modem establishes a connection with your ISP, turn on your router. … Turn on the wired and wireless devices that are connected to your router’s network. kb.netgear.com/19755/
  3. TP-Link, TP-Link FAQ 2982 (US): internet light off or WAN port unplugged: confirm you are using an RJ45 Ethernet cable, not an RJ11 phone cable. … If the computer cannot connect through the modem, the problem is with the modem or your Internet service provider (ISP), not the TP-Link router. … plug the same Ethernet cable from the router's WAN port into one of its LAN ports. If both the Ethernet and Internet lights turn on, the router's WAN port hardware is functioning. … If both the Ethernet and Internet lights are OFF, the WAN port may be faulty, or the Ethernet cable may be faulty . … set the internet port negotiation speed to 100 Mbps full duplex , and check whether the internet LED comes on. tp-link.com/us/support/faq/2982/
  4. NETGEAR, NETGEAR KB 27477: amber LEDs or a blinking power LED: the Power LED lights amber while the router boots, and then turns white or green when the router is ready to use. … Make sure that you are using the power adapter that was included with your router. … try plugging your router directly into a power outlet instead of a surge protector … If you use Ethernet cables to connect devices to the LAN ports on your router, disconnect them all and see if the router boots normally. … network loops are a common cause of router problems. … its firmware might be corrupt due to a failed update or a power outage during the update process. kb.netgear.com/27477/
  5. NETGEAR, NETGEAR KB 9665: what a factory reset deletes: A factory reset deletes all personalized settings including your user name, password, WiFi network name (SSID), and security settings. kb.netgear.com/9665/
  6. TP-Link, TP-Link FAQ 2478 (India): reboot schedule on a 4G LTE router: Auto Reboot allows you to specify a time when the router will reboot automatically. … Go to Advanced > System Tools > Reboot . … Enable Reboot Schedule . … Specify the time at which your router will reboot and the Auto Reboot Interval . … This feature takes effect based on the router’s system time. Please make sure you have configured the system time correctly. … Archer MR200 V3 V4 Archer MR600 V1 tp-link.com/in/support/faq/2478/

Author: Bulan Sarkar · Report an error

Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.