Will It Work? · Guide
An old router as an access point: menu, manual setup and what you lose
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
A router left over from an upgrade can add Wi-Fi to a room your main router does not reach, if a cable can get there. Set up as an access point, it joins the main router's network instead of starting its own. This guide follows two makers' support pages: when to use bridge mode on a provider's box instead, the menu way and the manual way to set it up, how to pick its address, and which features stop working.
Cable the old router to the main one and switch it to access point mode. With no such menu, set it up by hand: an address on the main router's segment but outside its DHCP range (one maker's example: 192.168.2.11 when DHCP runs 192.168.2.100-192.168.2.199), DHCP server off, and LAN port to LAN port. Routing features such as parental controls, QoS and VPN stop working.
What access point mode does
One maker says access point mode turns a wired network connection into a Wi-Fi network (TP-Link); the other says the router then runs on the same local network as the existing router or gateway, to widen the Wi-Fi coverage (NETGEAR). The main router keeps doing the routing and handing out addresses. The old one adds Wi-Fi, and its other LAN ports work as spare wired ports. If you have no cable route, the mesh, extender or access point guide covers the wireless options.
Behind a provider’s box: bridge first
When the main router is a box from your internet provider, one maker suggests a different order. If the box supports bridge mode, it recommends turning that on and installing your own router in router mode instead of AP mode (NETGEAR), cabled from the box's Ethernet port to your router's internet port (NETGEAR), so every router feature stays. If the box has no bridge mode, it says to turn the box's Wi-Fi off and use your router in AP mode (NETGEAR).
Without one: set it up by hand
For a router with no Operation Mode menu, one maker gives a manual method (TP-Link):
- Give the router a LAN address on the main router’s segment, outside its DHCP range, then log in again at the new address.
- Set the Wi-Fi name and password.
- Turn the DHCP server off (Advanced -> Network -> DHCP Server).
- Reboot.
- Connect a LAN port of the main router to a LAN port of this router (not its internet port).
Change the address before you turn DHCP off, and note it down: after the reboot the router answers only at the new address. Every other LAN port on the old router then gives wired devices internet access as well (TP-Link). The same maker notes that a router set up this way still technically runs in router mode with its internet port unused, so its routing menus still show but do nothing (TP-Link).
Choosing its address
The old router needs an address on the same segment as the main router and outside the main router's DHCP range. The maker's example: with DHCP at 192.168.2.100 to 192.168.2.199, set it to 192.168.2.11 (TP-Link). Inside the range, the main router could hand the same address to a phone later. Find the range on the main router's DHCP or LAN page. The address reservation guide explains segments and ranges in more detail.
What you lose in access point mode
Features that depend on the routing stop working. One maker lists Parental Controls, QoS, Bandwidth Control, NAT Forwarding, IPv6, VPN as unavailable because the internet port is no longer in use, while LED Control (Night Mode), Time Settings (NTP Server), Wi-Fi Schedule, Auto Reboot, USB Sharing keep working (TP-Link). The other greys out a longer list in AP mode, including Guest Network, Setup Wizard, Port Forwarding/Port Triggering, Remote Management, UPnP, IPv6, Traffic Meter, Parental Controls and 9 more (NETGEAR).
The guest network changes too. One maker says that in access point mode its guest network is no longer isolated from the main network, so devices on it can reach the main network (TP-Link); the other turns the guest network off in AP mode (NETGEAR). If you need a separate guest network, run it on the main router; the guest and IoT network guide shows how.
Tips and tricks
- Look for the mode under Operation Mode or Wireless AP; with neither, use the manual method.
- Write down the old router’s new address before you turn its DHCP server off.
- Use LAN ports on both routers for the manual method; leave the old router’s internet port empty.
- Do not count on the old router’s guest network in AP mode; set guests up on the main router.
- Behind a provider’s box, check its settings for bridge mode before you choose AP mode.
- Give the old router the same Wi-Fi name as the main router; one phone maker advises one name on every router in a home.
What we would do
Behind a provider's box with bridge mode, we would bridge the box and run our own router in router mode. Otherwise we would cable the old router to the main one and use its access point mode, or the manual method with an address such as 192.168.2.11 outside a 192.168.2.100-192.168.2.199 DHCP range. We would keep parental controls and the guest network on the main router.
Questions people ask
Can I use an old router as an access point? Usually, yes. Many routers have an access point mode in an Operation Mode or Wireless AP menu. One maker also gives a manual way for routers without that menu: set its address on the main router’s segment outside the DHCP range, turn its DHCP server off, and connect LAN port to LAN port.
Which port do I use on the second router? For the manual method, one maker says to connect a LAN port on the main router to a LAN port on the second router; any LAN port works. The internet (WAN) port is not used. Routers with an access point mode follow their own setup guide.
Why does the second router need DHCP turned off? So that only the main router hands out addresses. One maker’s manual method turns the second router’s DHCP server off and gives the router itself an address outside the main router’s DHCP range, so the two never hand out or use the same address.
What stops working in access point mode? Features that need the router to do the routing stop working. Both makers whose pages we read list Parental Controls, QoS, NAT Forwarding, IPv6, VPN among them. One maker adds that its guest network is no longer kept apart from the main network in access point mode, so guests can reach your devices.
Should I use access point mode behind my provider’s router? One maker recommends bridge mode on the provider’s box and router mode on your router where the box supports it, so every feature keeps working. If the box has no bridge mode, it says to turn the box’s Wi-Fi off and put your router in access point mode.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- TP-Link, TP-Link FAQ 1384 (US): How to Set Up a TP-Link Router as an Access Point:
Access Point mode lets you use a TP-Link router as a wireless access point, turning a wired network connection into a Wi-Fi network. … The setup process is different depending on whether your router has an Operation Mode menu. … Connect the router to your wired host router’s Ethernet port via an Ethernet cable … Go to Advanced > Operation Mode or Advanced > System > Operation Mode to switch to Access Point Mode. … change the LAN IP address of your TP-Link router to an IP address on the same segment as the main router. This IP address should be outside the main router’s DHCP range. … Example: If your DHCP is 192.168.2.100 -192.168.2.199, then you can set the IP to 192.168.2.11 … After changing the LAN IP address, a reboot is required, and you will need to log in to the TP-Link router with the new IP address. … Go to Advanced -> Network -> DHCP Server and Disable the DHCP Server . … Use an Ethernet cable to connect the main router to your TP-Link router through their LAN ports (any LAN ports may be used).
tp-link.com/us/support/faq/1384/ - TP-Link, TP-Link FAQ 2420 (US): Access Point Mode vs Router Mode:
In Access Point mode, the router provides some basic functions only. Gateway-dependent features, including Parental Controls, QoS, Bandwidth Control, NAT Forwarding, IPv6, and VPN, are unavailable because the WAN port is no longer in use. … Some features work in both Router mode and Access Point mode, including LED Control (Night Mode), Time Settings (NTP Server), Wi-Fi Schedule, Auto Reboot, and USB Sharing. … In Access Point mode, the Guest Network is no longer isolated from the main network. Devices on the guest network can access the main network. … After disabling the DHCP server, the router technically still operates in Router mode but no longer uses the WAN port. … can still be found in the router's interface but will not function.
tp-link.com/us/support/faq/2420/ - NETGEAR, NETGEAR KB 20927: How do I change my NETGEAR router to AP mode?:
You can set up your NETGEAR router to run in access point (AP) mode on the same local network as another existing router or gateway to expand the wireless coverage in your home. … If you are installing your router with an ISP gateway that supports bridge mode, we recommend that you enable bridge mode on your ISP gateway and install your NETGEAR router in router mode instead of AP mode. … Before changing your router to AP mode, you must complete basic router setup. … Select ADVANCED > Advanced Setup > Wireless AP . … Some models might use slightly different menu labels, like Router / AP / Bridge Mode . … Get dynamically from existing router is selected by default. Only use the Enable fixed IP settings on this device (not recommended) setting if you have advanced network experience … You lose the Internet connection between your router (now configured as an AP) and your computer.
kb.netgear.com/20927/How-do-I-change-my-NETGEAR-router-to-AP… - NETGEAR, NETGEAR KB 000061927: What is the difference between router mode and AP mode?:
In router mode, your NETGEAR device functions normally and all of the router’s features are available. … However, some popular features are disabled in AP mode, including the following: Guest network The ability to block specific websites VPN Service Remote Management … If you cannot enable bridge mode on your ISP gateway, you must turn off the WiFi on your ISP gateway and install your NETGEAR or Orbi router in AP mode.
kb.netgear.com/000061927/What-is-the-difference-between-rout… - NETGEAR, NETGEAR KB 26765: Which features are disabled on my NETGEAR router when it is set to AP Mode:
The following features are not available (grayed out) when your NETGEAR router is in AP mode: Guest Network Setup Wizard Port Forwarding/Port Triggering Remote Management UPnP IPv6 Traffic Meter Parental Controls Circle Netgear Armor Block Sites Block Services VPN Service VLAN/IPTV Setup Internet Setup WAN Setup LAN Setup Access Control QoS
kb.netgear.com/26765/Disabled-Features-on-the-Router-when-se… - NETGEAR, NETGEAR KB 26748: How do I install my NETGEAR or Orbi router after I enable bridge mode or turn the WiFi off on my ISP gateway?:
You might want to do this if your ISP requires you to use a gateway with poor WiFi performance. … Use an Ethernet cable to connect the Ethernet port of your ISP gateway to the Internet port of your NETGEAR or Orbi router.
kb.netgear.com/26748/How-do-I-install-my-NETGEAR-or-Orbi-rou… - Apple, Apple Support 102766: Recommended settings for Wi-Fi routers (network name):
Set to a single, unique name (case-sensitive) for all bands. … Make sure that all routers on your network use the same name for every band they support. If you give your 2.4 GHz, 5 GHz, or 6 GHz bands different names, devices might not connect reliably to your network, to all routers on your network, or to all available bands of your routers. … Don't use common names or default names such as linksys , netgear , dlink , wireless , or 2wire . Otherwise, devices that join your network are more likely to encounter other networks that have the same name, and then automatically try to connect to them.
support.apple.com/en-us/102766