Will It Work? · Guide

Smart plugs and bulbs on 2.4 GHz: getting setup to work

By , founder of ElectronicsInfoline (since 2000)

Smart plugs, bulbs and older thermostats often have a 2.4 GHz radio only, while modern routers and mesh systems often put 2.4 and 5 GHz under one network name. The two meet at setup, when the app on your phone has to hand the plug your Wi-Fi details. This guide explains why that step fails, which router settings one plug maker asks for, and how to change routers without setting every device up again. It draws on the makers' own setup FAQs.

The device needs 2.4 GHz turned on, and during setup the phone should be on 2.4 GHz too. On a router with one name for every band, join a separate 2.4 GHz name or stand farther away until the phone drops to 2.4 GHz. If it still fails, set 2.4 GHz to channel 1, 6, 11, 20 MHz wide and WPA2, and set devices up one at a time.

Why 2.4 GHz-only devices fail setup

One maker says its current smart plugs and switches support only 2.4 GHz Wi-Fi (TP-Link), and its other plug range works with any router that supports 2.4 GHz (TP-Link). Another maker lists its 1st and 2nd gen learning thermostats, 1st and 2nd gen smoke alarms and a bridge as 2.4 GHz only, and says you need 2.4 GHz turned on in the router to connect them (Google).

Setup apps usually need the phone on the same band as the device, but a mesh system with one name for both bands often puts the phone on 5 GHz, and setup fails (TP-Link). A mesh maker explains why it happens: one name covers every band, and each device maker writes its own rules for choosing a band (Google), so the phone picks its band, not the router.

Why setup fails on a one-name dual-band networkA router broadcasting one network name on 2.4 GHz and 5 GHz. Left: the phone has joined on 5 GHz, while the smart plug can only use 2.4 GHz, so the setup app on the phone and the plug are on different bands and setup can fail. Right: with the phone moved to 2.4 GHz, for example by joining a separate 2.4 GHz name or walking farther from the router, both are on 2.4 GHz and setup can finish.setup can failrouterone name: 2.4 + 5 GHzphone5 GHzplug2.4 GHz onlydifferent bandssetup can finishrouterone name: 2.4 + 5 GHzphone2.4 GHzplug2.4 GHz onlysame band
Figure 1. Two makers say the setup app may need the phone on the same 2.4 GHz band as the device. A separate 2.4 GHz name, or standing farther from the router, puts it there.

Getting the phone onto 2.4 GHz

One mesh maker says you may need to connect your phone to the 2.4 GHz band by hand for setup, and if the phone cannot choose a band, to move farther from the router until it switches to 2.4 GHz (Google). On routers that allow it, a separate 2.4 GHz network name does the same job without the walk; the network name guide shows how to split one band off and when that helps. Some routers also offer a separate IoT network that keeps smart devices on 2.4 GHz; the guest and IoT network guide covers it.

The 2.4 GHz settings to check

When a plug cannot find the home network or fails to pair, its maker asks for three router changes on 2.4 GHz: channel 1, 6, 11, a 20 MHz channel width, and WPA2 security (TP-Link). A thermostat maker also recommends WPA2 for its products (Google). The plug maker lists WPA-PSK, WPA2-PSK, WPA3 as the security types its plugs accept, and says they cannot join a network behind a sign-in page (captive portal) (TP-Link). The channel and width guide explains why those three channels and that width.

2.4 GHz settings for smart-device setupThe 2.4 GHz channel numbers 1 to 11 on a line. Three 20 MHz blocks sit on channels 1, 6, 11, which do not overlap one another. Below them: channel width 20 MHz and security WPA2, the settings one smart-plug maker asks for when its devices cannot find the network or fail to pair.123456789101120 MHz20 MHz20 MHz2.4 GHz channel numberchannel width20 MHzsecurityWPA2
Figure 2. One smart-plug maker's settings for a failed setup: channel 1, 6, 11, 20 MHz wide, WPA2. Channels 1, 6 and 11 are the ones that do not overlap in North America; the channel guide covers other regions.

Setup problems, step by step

One plug maker sorts failed setups by where they stop (TP-Link). These are its steps for each, in its order:

The app cannot find the device

  1. Power on one device at a time when setting up several.

Your home network is not in the list

  1. Move the device closer to the router.
  2. Make sure the home network is on 2.4 GHz.
  3. Type the network name and password by hand (Other Network).
  4. Set the router's 2.4 GHz to channel 1, 6, 11, 20 MHz wide, WPA2.

It will not connect to your network

  1. Forget the network on the phone and rejoin it to prove the password.
  2. Check the router is not at its device limit.

Pairing fails at the end

  1. Forget the network on the phone and rejoin it to prove the password.
  2. Set the router's 2.4 GHz to channel 1, 6, 11, 20 MHz wide, WPA2.
  3. Try a phone hotspot; if it joins, update the device firmware, reset it and try the router again.

After a new router

A new router does not have to mean setting every plug and bulb up again. One maker says its devices recognise a network by its name (SSID), security type and password, so setting the new router to the same name and password as the old one lets them rejoin (TP-Link). Keep the security type the same as well: a move from WPA2 to WPA3 changes one of the three. Network names are case-sensitive (Apple), so copy them exactly.

Swapping the router without re-adding every deviceTwo columns compare an old router and a new one on three items: network name, security type and password. In the first case all three match, so the smart devices rejoin by themselves. In the second the security type changed from WPA2 to WPA3, so the devices treat it as a different network and each needs setting up again.old routernew routernetwork namesame network nameWPA2WPA3 here: changedpasswordsame passwordall three the same: devices rejoinany one different: set each device up again
Figure 3. One maker says its devices recognise a network by name, security type and password. Copy all three to the new router, matching upper and lower case, and the devices rejoin.

Tips and tricks

  • Check the box or the maker’s page for the Wi-Fi band before buying: 2.4 GHz only is common on plugs and bulbs.
  • Put the phone on 2.4 GHz before opening the setup app, not halfway through.
  • Set up several devices one at a time; one maker says powering them all at once can make setup fail.
  • If the network is not listed, type its name and password by hand (Other Network).
  • Prove the password first: forget the network on the phone and rejoin it.
  • When you replace the router, copy the old name, password and security type before switching it off.

What we would do

We would put the phone on 2.4 GHz first, by a separate 2.4 GHz name if the router allows it, and set devices up one at a time near the router. If a plug still would not pair, we would set 2.4 GHz to channel 1, 6, 11, 20 MHz and WPA2, and try again. Before any router swap, we would write down the old name, password and security type and copy all three.

Questions people ask

Why will my smart plug not connect to 5 GHz Wi-Fi? Many smart plugs and bulbs have a 2.4 GHz radio only. One maker says its current plugs and switches support only 2.4 GHz Wi-Fi, and another says its plugs do not support 5 GHz. They work with any router that has 2.4 GHz turned on.

Do I need to turn off 5 GHz to set up a smart plug? Not according to the makers whose pages we read. What they ask for is the phone on 2.4 GHz during setup. Join a separate 2.4 GHz network name if the router has one, or, as one maker suggests, walk farther from the router until the phone moves to 2.4 GHz.

Why does setup fail on a mesh system with one network name? The setup app on the phone usually needs the phone on the same band as the device. With one name for every band, the phone often joins on 5 GHz while the plug can only use 2.4 GHz. Put the phone on 2.4 GHz for setup, or use the router’s IoT network if it has one.

Will my smart devices still work if I change my router? They will rejoin if the new router uses the same network name, security type and password, because one maker says that is how its devices recognise a network. Change any of the three and each device has to be set up again.

Which Wi-Fi security works with smart plugs? One maker lists WPA-PSK, WPA2-PSK, WPA3 for its plugs, and says they cannot join a network that needs a sign-in page (captive portal), as in hotels. When setup fails, the same maker suggests WPA2 on the 2.4 GHz band.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. TP-Link, TP-Link FAQ 2615 (US): what if I fail to configure the Tapo smart plug: Step 4. If you need to configure multiple devices, power on one device at a time to avoid setup failure. … Step 1. Move the smart device closer to your router to ensure a strong signal strength. Step 2. Ensure your home Wi‑Fi network is on 2.4 GHz; the Tapo device does not support 5 GHz. … Step 4. Choose “ Other Network ” to input the SSID and password manually. Step 5. Change the router's 2.4GHz Wi-Fi settings: set channel to 1, 6, or 11; bandwidth to 20 MHz; and encryption method to WPA2. … We recommend " forgetting " the network on your phone and rejoining it to confirm the password works. … Step 5. Ensure the router has not reached its maximum device limit. … Step 5. Attempt to connect the device to a mobile hotspot. If successful, update the device's firmware within the App, then reset it and try connecting to the router again. tp-link.com/us/support/faq/2615/
  2. TP-Link, TP-Link FAQ 3417 (US): Tapo smart plug common questions: The Tapo smart plug is compatible with any wireless router that supports 2.4 GHz frequency. … Can the Tapo Smart Plug join a captive portal-secured wireless network? No, the Tapo Smart Plug only supports WPA-PSK, WPA2-PSK, and WPA3 for wireless security. … Set your wireless network to the same name and password as your old router. You don't need to set up the Tapo Smart Plug from scratch because the smart home device recognizes networks by their SSID, security type, and password. tp-link.com/us/support/faq/3417/
  3. TP-Link, TP-Link FAQ 1390 (US): Kasa smart home common questions: Current Kasa products support only 2.4 GHz Wi-Fi and do not support ZigBee, Z-Wave, IPv6, or Ethernet. tp-link.com/us/support/faq/1390
  4. Google, Google Nest Help 6293481: how Nest Wifi and Google Wifi bands work: A single network name is used across all the bands. … Every wireless device is different and each manufacturer develops its own rules for choosing the best band. … some smart home devices can only use the 2.4 Ghz band and do not support 5 and 6 Ghz. To set up these devices, you may need to manually connect your phone to the 2.4 Ghz Wi-Fi band. … If your phone doesn't have the ability to switch Wi-Fi bands, try to move farther away from your router and point until your phone moves to the 2.4 GHz band. support.google.com/googlenest/answer/6293481?hl=en
  5. Google, Google Nest Help 9240155: Wi-Fi network and router settings for Nest products: 1st and 2nd gen Nest Learning Thermostats, 1st and 2nd gen Nest Protects, and Nest Connect only work with 2.4 GHz Wi-Fi. If you have one of these products in your home, you need to enable 2.4 GHz on your router to connect them. … It's recommended to use WPA2 encryption on your router when using Nest products. support.google.com/googlenest/answer/9240155?hl=en
  6. TP-Link, TP-Link FAQ 4420 (US): smart home devices on a mesh network: Most IoT devices only work on 2.4GHz, and their setup apps require your phone to be on the same band. But Deco mesh uses one Wi-Fi name for both 2.4GHz and 5GHz, so your phone often connects to 5GHz, causing setup failures. An IoT Network solves this by keeping everything on the same 2.4GHz Wi-Fi. tp-link.com/us/support/faq/4420/
  7. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers (network name): Set to a single, unique name (case-sensitive) for all bands. … Make sure that all routers on your network use the same name for every band they support. If you give your 2.4 GHz, 5 GHz, or 6 GHz bands different names, devices might not connect reliably to your network, to all routers on your network, or to all available bands of your routers. … Don't use common names or default names such as linksys , netgear , dlink , wireless , or 2wire . Otherwise, devices that join your network are more likely to encounter other networks that have the same name, and then automatically try to connect to them. support.apple.com/en-us/102766

Author: Bulan Sarkar · Report an error

Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.