Will It Work? · Guide

Wi-Fi channel and channel width: which settings to use

By , founder of ElectronicsInfoline (since 2000)

The Wi-Fi page on a router has two settings people change when the connection gets slow: the channel and the channel width. This guide sets out what three makers recommend for each band, which 2.4 GHz channels do not overlap, and which channel a second box (an extender or another router) should use. It is drawn from those makers' own support pages.

Leave the channel on Auto on every band unless you get dropped connections or slow transfers. Set the width to 20 MHz on 2.4 GHz and Auto (or all widths) on 5 and 6 GHz. If you pick a 2.4 GHz channel by hand, use 1, 6, 11 in the USA (one maker gives 1, 7, 13 for Europe). An extender stays on the router's channel; a second router gets its own.

Start with Auto

One maker says to set the channel to Auto, so the router picks the best channel itself (Apple). Another says to keep the channel and channel width on their defaults unless you face interference from nearby networks (TP-Link). On the third maker's routers the router already picks its 2.4 GHz channel from what it sees around it and uses default 5 GHz and 6 GHz channels for your region, and the maker recommends the defaults unless you have interference (NETGEAR).

Interference shows up as lost connections or slow data transfers (NETGEAR). If you see neither, leave the settings alone. For a slow connection, the Wi-Fi speed vs internet speed guide covers the other common causes first.

Channel width per band

Channel width is how wide a pipe the router uses. Wider channels are faster but more open to interference, and more likely to cause it (Apple). The same maker recommends 20 MHz on 2.4 GHz, a band shared with other Wi-Fi networks and with Bluetooth devices, and Auto or all widths on 5 GHz and 6 GHz, where interference is less of a concern (Apple).

Channel width to set on each Wi-Fi band2.4 GHz: 20 MHz, because the band is shared with nearby networks and Bluetooth devices. 5 GHz: Auto or all widths. 6 GHz: Auto or all widths. A wider channel is a bigger pipe and faster, but picks up and causes more interference. Channel itself: Auto on every band.2.4 GHzcrowded: neighbours, Bluetooth20 MHz5 GHzinterference less of a concernAuto or all widths6 GHzinterference less of a concernAuto or all widthsBar = how wide a pipe the setting allows (not to scale).
Figure 1. One maker's settings. Wider channels are faster but more open to interference, so the crowded 2.4 GHz band stays at 20 MHz and the router picks the width on 5 and 6 GHz. Channel: Auto everywhere.

2.4 GHz channels: 1, 6 and 11

One maker's channel page says 2.4 GHz devices can use one of 11 channels in North America and 13 in Europe, and that the non-overlapping ones are 1, 6, 11 in the USA and 1, 7, 13 in Europe (NETGEAR). Which channels your router offers follows its Region setting, and not every channel is available in every region (NETGEAR).

If two nearby networks cannot both sit on one of those three, keep them as far apart as you can. The same maker gives two different figures: at least 5 channels apart on one page (1 and 6, or 4 and 10) (NETGEAR), and 4 apart between neighbouring access points on another (1 and 5, or 6 and 10) (NETGEAR). Channels 1, 6 and 11 are 5 apart, so they meet both.

2.4 GHz channels and the three that do not overlapUSA: channels 1 to 11; the three that do not overlap are 1, 6, 11. Europe: channels 1 to 13; one maker names 1, 7, 13. If you cannot use one of the three, keep neighbouring networks as far apart as you can: the same maker says at least 5 channels apart on one page and 4 on another.USA1234567891011121311 channels; blue = 1, 6, 11; dashed = not offeredEurope1234567891011121313 channels; blue = 1, 7, 13Spacing check: 1 and 6 are 5 apart; 6 and 11 are 5 apart.
Figure 2. One maker's non-overlapping 2.4 GHz channels: 1, 6 and 11 in the USA; 1, 7 and 13 in Europe. Your router's Region setting decides which channels it offers.

5 GHz and 6 GHz channels

Part of the 5 GHz band is shared with radar. On those channels Dynamic Frequency Selection (DFS) is a legal requirement: the router watches for radar and switches to another frequency when it detects it (NETGEAR). Before choosing a DFS channel by hand, check that your router supports DFS (NETGEAR).

On 6 GHz, if you set the channel yourself, pick a preferred scanning channel (PSC); otherwise devices may have trouble connecting to the band (NETGEAR). The Wi-Fi 6E guide covers what else 6 GHz needs.

Extenders and a second router

An extender repeats the router's network. One maker says that if you change the router's channels, you must set the extender to the same channels (NETGEAR). A second router or access point is a separate cell; another maker says to give each router its own channel, especially when they are close together (Apple). The mesh, extender or access point guide explains the difference between the three.

Which channel a second Wi-Fi box should useLeft: a router on channel 6 and a Wi-Fi extender that repeats it: the extender uses the same channel as the router; if you change the router's channel, set the extender to match. Right: a router on channel 1 and a second router or access point close by: it uses a different channel from the router, for example 6 or 11 on 2.4 GHz. Channel numbers here are examples.extendersecond router or AProuterchannel 6extenderchannel 6same channelrepeats the routerrouterchannel 1second unitchannel 6 or 11different channelits own network cell
Figure 3. An extender repeats the router's network, so one maker says to keep it on the router's channels. Separate routers or access points should each have their own channel, especially when they sit close together.

Where the settings are

On one maker's routers, go to Advanced > Wireless > Wireless Settings, change the channel or width for a band, and Save (TP-Link). On another's, log in, select Wireless, scroll to the band, choose a number from the Channel menu and click Apply (NETGEAR). Change one band at a time and use the connection for a while before you decide whether it helped.

Tips and tricks

  • Leave channel and width on Auto first. Change them only for lost connections or slow transfers.
  • On 2.4 GHz, use 20 MHz, and pick 1, 6 or 11 (USA) if you choose by hand.
  • Do not set 2.4 GHz to 40 MHz to go faster: wider means more interference on that band.
  • If you change the router’s channel, set an extender to match it.
  • Give a second router or access point a different channel from the first.
  • On 6 GHz, choose a preferred scanning channel if you set one by hand.

What we would do

We would leave both settings on Auto, apart from the 2.4 GHz width, which we would set to 20 MHz. Only with dropped connections or slow transfers would we try 1, 6 or 11 on 2.4 GHz, one change at a time, and we would keep any extender on the router's channel.

Questions people ask

What channel width should I use on 2.4 GHz? 20 MHz. Wider channels are faster but pick up and cause more interference, and the 2.4 GHz band is shared with neighbouring networks and Bluetooth devices. On 5 GHz and 6 GHz, set the width to Auto or allow all widths.

Which 2.4 GHz channel is best: 1, 6 or 11? They are the three that do not overlap in the USA, so pick whichever of them your neighbours use least. One maker gives 1, 7 and 13 for Europe. Most routers pick a channel themselves on Auto, which is the right setting unless you see dropped connections or slow transfers.

Should I set my Wi-Fi channel to Auto? Yes, on every band, unless you have interference you can see: lost connections or slow transfers. All three makers whose pages we read say to leave the channel on Auto or the default and change it only then.

Should my extender be on the same channel as my router? One maker says yes: an extender repeats the router, and if you change the router’s channel you must set the extender to the same channels. A second router or access point is different: give it its own channel, especially if it sits close to the first.

What are DFS channels on 5 GHz? Channels shared with radar. Dynamic Frequency Selection is a legal requirement there: the router listens for radar and moves to another channel when it detects it. Check that your router supports DFS before picking one of those channels by hand.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers (channel and channel width): Channel Set to Auto. … When channel selection is set to automatic, your router … use a different channel, especially if they are close to each other. … Set to 20 MHz for the 2.4 GHz band. Set to Auto or all widths for the 5 GHz and 6 GHz bands. … Wider channels are faster but more susceptible to interference … including Bluetooth devices. … Wireless interference is less of a concern in these bands. support.apple.com/en-us/102766
  2. TP-Link, TP-Link FAQ 2292 (US): changing Wi-Fi settings, channel and channel width: For advanced settings like Channel and Channel Width, keep default values unless you face interference. … Leave it on Auto unless you experience interference from nearby networks. … Go to Advanced > Wireless > Wireless Settings , make your changes, and Save . tp-link.com/us/support/faq/2292/
  3. NETGEAR, NETGEAR KB 23783: changing the wireless channel: Your router automatically selects a 2.4 GHz channel based on your network environment, and uses default 5 GHz (and 6 GHz, if equipped with WiFi 6E or newer) channels based on your region. … We recommend that you use the default wireless channels unless you experience interference. … If you change your 6 GHz wireless channel, we recommend that you select a PSC, or your devices might experience difficulty connecting to the 6 GHz band. … Due to regional wireless broadcast regulations, not all channels are available in all regions. … If you use WiFi extenders, and you changed your router’s wireless channels, you must also set your extenders up to use the same channels as your router. kb.netgear.com/23783/
  4. NETGEAR, NETGEAR KB 1027: selecting wireless channels: You are experiencing interference (shown by lost connections or slow data transfers). … Devices that use 802.11b and 802.11g can be tuned to one of 11 channels in North America, 13 channels in Europe. … These are channels 1, 6 & 11 in USA. Channels 1, 7 & 13 in Europe. … choose channels as widely spaced as possible, preferably at least five channels apart. For example, use channels 1 and 6, or channels 4 and 10. kb.netgear.com/1027/
  5. NETGEAR, NETGEAR KB 24095: basic wireless settings (channel spacing between access points): Do not change the channel unless you experience interference (shown by lost connections or slow data transfers). … The recommended channel spacing between adjacent access points is four channels (for example, use Channels 1 and 5, or 6 and 10). kb.netgear.com/24095/
  6. NETGEAR, NETGEAR KB 000060371: what Dynamic Frequency Selection (DFS) is: Dynamic Frequency Selection (DFS) is a legally required feature for all WiFi devices that share the 5 GHz band with radar. … DFS enables a router or AP to detect radar signals and switch their operating frequency to prevent interference. kb.netgear.com/000060371/
  7. NETGEAR, NETGEAR KB 000060373: choosing a DFS channel: Before selecting a DFS channel for your router, please see the following article to make sure your router supports DFS kb.netgear.com/000060373/

Author: Bulan Sarkar · Report an error

Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.