Will It Work? · Guide
PoE, PoE+ and PoE++: will the switch power your device?
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
A ceiling access point or a camera over the door is much easier to fit when one Ethernet cable brings both data and power. That is Power over Ethernet (PoE). The catch is that “PoE” covers four power levels, and the switch has to be at least as high as the device. The figures here come from two network makers' pages that set out the IEEE tiers (the IEEE text itself is behind a sign-in).
The four tiers and their watts
Each IEEE standard raises the power a switch port can send. The switch side is called the PSE (power sourcing equipment); the device is the PD (powered device). Two maker pages give the same figures (TP-Link Omada) (NETGEAR):
- PoE, 802.3af (2003): up to 15.4 W at the port, 12.95 W at the device.
- PoE+, 802.3at (2009): up to 30 W at the port, 25.5 W at the device.
- PoE++ Type 3, 802.3bt (2018): up to 60 W at the port, 51 W at the device.
- PoE++ Type 4, 802.3bt (2018): up to 90 W at the port, 71.3 W at the device.
The gap between the two figures is what the cable loses on the way (NETGEAR), so the device figure is the one to set against a device's needs. Watch the names: “PoE++” is a marketing term that covers both Type 3 and Type 4, so check which type a product supports (TP-Link Omada). “PoE+++” has no IEEE definition and no standard wattage at all (TP-Link Omada).
Pairs, cable and distance
An Ethernet cable has four twisted pairs. PoE and PoE+ use 2 of them for power; PoE++ uses all four (TP-Link Omada) (NETGEAR). The cable does not have to change: Cat5e or better supports all three PoE standards (TP-Link Omada), and each one delivers power over at most 100 m (328 ft) per cable segment (TP-Link Omada). Which cable suits which data speed is a separate question, covered by the Ethernet cable checker.
Will this switch power that device?
PoE is backwards-compatible in one direction only: a higher-standard switch can power a lower-standard device, but not the other way around (TP-Link Omada). A 15.4 W PoE switch cannot supply a PoE++ device that needs 60 W; the device will either fail to power on or run in a reduced state (TP-Link Omada).
A device without PoE can still go on a PoE switch. Before the switch applies any voltage, it and the device go through detection and classification, which confirms the power class and is there to prevent damage to non-PoE equipment (TP-Link Omada).
The switch’s total budget
Watts per port are not the only limit. A switch has one total PoE budget that all its active ports share. Omada's example: a 24-port switch with a 250 W budget cannot deliver 25.5 W to all 24 ports at once (TP-Link Omada). The sum shows why: 24 × 25.5 W = 612 W. At the full PoE+ port figure of 30 W, 250 W covers 8 ports at once (250 ÷ 30 = 8.33).
For your own setup, the same page says to add up what all the connected devices actually draw at the same time, and leave headroom (TP-Link Omada). Each device's draw is on its datasheet; the budget is on the switch's spec sheet.
No PoE port? Use an injector
If your router or switch has no PoE ports, a PoE injector adds PoE to one port of an existing non-PoE switch: it draws mains power and puts PoE onto the cable between the switch and the device (TP-Link Omada). The same tier rule applies: the injector's tier must be the device's tier or higher. Where the access point should go, and whether you need one at all, is covered in mesh, extender or access point.
Tips and tricks
- Read the device's datasheet for its IEEE tier (802.3af, at or bt) or its watt draw. The product title is not enough: "PoE" in a listing can mean any tier.
- With PoE++, check for Type 3 or Type 4 in the spec. The name covers both, and they differ by 30 W at the port.
- Compare against the device figure, not the port figure. A device that needs 20 W is within PoE+ (25.5 W at the device), not plain PoE (12.95 W).
- Look for two numbers on a PoE switch: watts per port and the total PoE budget. A switch with many PoE+ ports may not run them all at full power at once.
- Keep each cable run under 100 m (328 ft). Past that, the makers' figures no longer apply.
What we would do
For one access point or camera on a home network, we would use a single injector of the device's tier rather than buy a PoE switch. For three or more devices, we would pick a switch whose per-port tier matches the hungriest device and whose total budget covers the sum of every device's datasheet draw with some left over. When in doubt between PoE+ and PoE++, we would let the device's datasheet decide, not the box.
To keep PoE gear running in a power cut, the switch or injector goes on the backup with the router; the power-cut backup calculator works out how long a battery lasts.
Questions people ask
What is the difference between PoE, PoE+ and PoE++? How much power each switch port can put out. PoE (802.3af) gives up to 15.4 W, PoE+ (802.3at) up to 30 W, and PoE++ (802.3bt) up to 60 W (Type 3) or 90 W (Type 4). The device gets a little less after the cable: 12.95, 25.5, 51 and 71.3 W.
Can a PoE+ switch power a PoE device? Yes. A higher-tier port powers devices of its own tier and lower ones. The reverse does not work: a lower-tier port cannot supply a device that needs more, and the device may not start or may run in a reduced state.
Do I need a special cable for PoE? Cat5e or better works with all three PoE standards, for runs up to 100 m (328 ft) per cable segment. PoE++ uses all four pairs in the cable, but the cable stays the same; the switch port is what needs the higher rating.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- TP-Link Omada, Omada blog 2595: PoE vs. PoE+ vs. PoE++ (07-23-2026), comparison table:
PoE 802.3af 2003 15.4W 12.95W 44-57V 2 of 4 VoIP phones, basic cameras, single-radio APs PoE+ 802.3at 2009 30W 25.5W 50-57V 2 of 4 Wi-Fi APs, IR cameras, video conferencing PoE++ Type 3 802.3bt 2018 60W 51W 50-57V 4 of 4 Wi-Fi 7 APs, PTZ cameras, enterprise APs PoE++ Type 4 802.3bt 2018 90W 71.3W 50-57V 4 of 4
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - NETGEAR, NETGEAR blog: Overview of Official PoE Standards (updated 21 Oct 2025), comparison table:
Power at PD 12.95 W 25.50 W 51 W 71.3 W Max Power from PSE 15.40 W 30.0 W 60 W 90 W
netgear.com/hub/business/av/poe-standards-explained/ - NETGEAR, NETGEAR blog: Overview of Official PoE Standards (cable losses):
delivers up to 15.4 watts of DC power over Cat5 cables, with approximately 12.95 watts usable after accounting for cable losses.
netgear.com/hub/business/av/poe-standards-explained/ - NETGEAR, NETGEAR blog: Overview of Official PoE Standards (four pairs):
PoE++ or 4PPoE uses all four twisted pairs in a network cable to deliver increased power.
netgear.com/hub/business/av/poe-standards-explained/ - TP-Link Omada, Omada blog 2595: the PoE++ name:
"PoE++" is a marketing term encompassing both Type 3 and Type 4; when evaluating equipment, verify which type it supports, as the wattage difference is significant.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: PoE+++:
As for "PoE+++": it has no IEEE definition and no standardized wattage.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: backwards compatibility:
PoE is backwards-compatible: a higher-standard switch can power a lower-standard device, but not the other way around.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: a lower-tier switch on a higher-tier device:
A 15.4W PoE switch physically cannot supply a PoE++ device that requires 60W: the device will either fail to power on or operate in a degraded state.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: detection and classification:
Before applying voltage, the PSE and PD perform detection and classification to confirm the device's power class and prevent damage to non-PoE equipment.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: cable category:
Cat5e or better supports all three PoE standards.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: cable run:
All three PoE standards deliver power over a maximum of 100m (328 ft) per cable segment.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: power budget:
Total PoE capacity is shared across all active ports: a 24-port switch with a 250W budget cannot simultaneously deliver 25.5W to all 24 ports. Sum the realistic concurrent draw of all connected devices and build in headroom.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov… - TP-Link Omada, Omada blog 2595: PoE injector:
A PoE injector adds PoE to a single port on an existing non-PoE switch. It draws AC power and injects PoE onto the cable between the switch and the device.
omadanetworks.com/us/blog/2595/poe-vs-poe+-vs-poe++-power-ov…