Will It Work? · Guide

Powerline adapters: what speed you really get

By , founder of ElectronicsInfoline (since 2000)

A powerline kit sends your network over the house wiring: one adapter by the router, one in the room that needs a cable. Whether you get a usable wired link depends on the rate the pair reports, the Ethernet port and how the adapters are plugged in. The figures below come from one maker's kit spec pages for the US and India and its own support answers.

Expect 20 to 30% of the rate the adapters report, never the box figure, and no more than the Ethernet port allows: a 10/100 port stops at 100 Mbps. Plug both adapters straight into wall sockets on the same circuit, not into a power strip or a UPS.

How a powerline pair works

The adapters come in sets of two or more (TP-Link). Connect one to a LAN port on the router, plug another into a wall socket in another room, and connect your TV or computer to that one by cable (TP-Link). Pressing the pair button on each adapter makes a private powerline network, so other adapters on the wiring can no longer join without being paired; you pair two devices at a time (TP-Link). The link is encrypted with 128-bit AES (TP-Link).

A powerline pair: one adapter by the router, one in the room that needs a cableAn Ethernet cable runs from a router LAN port to adapter A, plugged straight into a wall socket. The signal travels over the house wiring to adapter B in a wall socket in another room, on the same electrical circuit, and an Ethernet cable runs from adapter B to a TV or computer. The maker gives up to 300 metres over the wiring. Press the pair button on each adapter to make a private network.RouterEthernetAwallhouse wiring, same circuitup to 300 m on paperBwallTV orcomputerpair buttonon eachNot into a power strip, a surge protector or a UPS outlet.
Figure 1. Adapters work in pairs or larger sets: one cabled to the router, the others where you need a wired port. Each goes straight into a wall socket. The maker lists up to 300 metres over the wiring; interference and line quality bring that down.

The kit pages list a range of up to 300 metres over existing wiring (TP-Link)(TP-Link), and the maker's support page adds that noise, interference and line quality bring that down (TP-Link).

The speed you get: 20 to 30% of the reported rate

The figure on the box, such as AV600 or AV1000, is the maximum powerline rate at the physical layer, not the throughput you will see. The maker says actual throughput is typically 20 to 30% of that rate, depending on the wiring (TP-Link)(TP-Link). The US kit page says the same in its small print: maximum signal rates are physical rates, and actual throughput and range vary with interference, traffic, an AFCI breaker or a separate circuit (TP-Link).

Box rate, reported rate and the speed on the cableThe box figure, here 1,000 Mbps, is a physical-layer rate. The maker's example has adapters reporting 364 Mbps, and its rule of 20 to 30 percent gives about 73 to 109 Mbps on the cable. An adapter with a 10/100 Ethernet port tops out at 100 Mbps whatever the powerline rate.On the boxphysical rate1,000 MbpsAdapters reportmaker example364 MbpsOn the cable20 to 30% of that73–109 Mbps10/100 port: 100 Mbps ceilingGigabit-port adapters: the port allows up to 1,000 Mbps.
Figure 2. The box figure is the most the powerline link could signal, not a speed you will see. Take 20 to 30% of the rate the adapters report (the maker's app shows it) to get the cable speed. A 10/100 Ethernet port stops at 100 Mbps.

The maker works its own example: adapters reporting a powerline rate of 364 Mbps should give about 73 to 109 Mbps (TP-Link). That is 364 × 0.2 = 72.8 and 364 × 0.3 = 109.2, rounded. To compare it with a Wi-Fi link or your internet plan, see box speed vs internet speed.

The Ethernet port sets a ceiling

The AV600 kits we checked, US and India, have one 10/100 Mbps Ethernet port per adapter (TP-Link)(TP-Link). The maker says that caps their throughput at 100 Mbps (TP-Link), so a pair reporting 500 Mbps would work out at 100 to 150 Mbps on the powerline side and still stop at 100 on the cable.

The AV1000 kits have a gigabit port: the US wired kit lists a Gigabit Ethernet port (TP-Link), and the India kit lists 10/100/1000 Mbps (TP-Link). With a gigabit port, the cable side allows up to 1,000 Mbps, more than the 200 to 300 Mbps that 20 to 30% of a 1,000 Mbps box rate gives. If you need more than about 100 Mbps on the cable, the port line on the spec page is the first thing to read.

Three checks before you blame the adapters

Three checks before blaming the adapters1. Straight into a wall socket? If not: Strip or surge protector: rate drops. 2. Both on the same circuit? If not: Separate circuits: no link. 3. Not through a UPS? If not: A UPS filters the signal out. Then: mixed adapters run at the slowest one's rate, and every adapter on one network shares the bandwidth.1. Straight into a wall socket?Strip or surge protector: rate drops2. Both on the same circuit?Separate circuits: no link3. Not through a UPS?A UPS filters the signal outThen:a mixed set runs at the slowest adapter; one network shares one rate
Figure 3. The maker names these three as the usual reasons a pair links slowly or not at all. After them: a mixed set runs at the slowest adapter's rate, and all adapters on one network share it.
  1. Straight into a wall socket. A power strip or surge protector can filter or block the signal and cut the rate a lot (TP-Link)(TP-Link).
  2. Same electrical circuit. The setup guide puts the second adapter on the same circuit (TP-Link). A pair that links in one room and loses the link in another is usually on separate circuits (TP-Link). Across the phases of a three-phase supply they still work, at a lower rate, and most breaker boxes have little effect (TP-Link).
  3. Not through a UPS. A UPS usually filters the line and can cut the powerline connection (TP-Link)(TP-Link).

The same support page names two other noise sources: appliances with motors, such as air conditioners, washing machines and fans, and phone and laptop chargers plugged in nearby (TP-Link).

Mixing adapters and adding more

Adapters on the same HomePlug standard work together, but the powerline rate drops to the slowest adapter's rate, so the maker recommends buying the same series (TP-Link). An AV1000 kit with an AV600 adapter added runs at the AV600 rate (600 on the box). The AV1000 kit page says it works with all HomePlug AV and AV2 adapters (TP-Link).

Each network has an adapter limit: the maker's table runs from 6 to 64, most current models allow 16, and in a mixed set the lowest limit applies (TP-Link). Every adapter on one network shares the whole bandwidth (TP-Link), so a third adapter shares the rate the first two had.

Power draw, and power cuts

The adapters draw little. The US gigabit adapter lists a maximum of 2.7 W and the US AV600 adapter 2.5 W (TP-Link)(TP-Link). The India AV600 adapter lists 4.6 W (TP-Link), and the India Wi-Fi kit lists 2.9 W for its wired unit and 11 W for its Wi-Fi unit (TP-Link).

The adapters take their power from the wall socket they sit in, so both sockets need power for the link to stay up. Running the adapters from a UPS outlet does not keep the link, because the UPS filters the signal (TP-Link). For keeping the router itself on in a cut, see the power-cut backup calculator and Wi-Fi in a power cut.

If the room only needs more coverage, not a cable, compare mesh, extenders and access points. If you can run a cable, a plain Ethernet run with a home Ethernet switch avoids the wiring question altogether.

Tips and tricks

  • Plug both adapters in side by side first and pair them there. If they link next to each other but not in the far room, the problem is the wiring between the rooms.
  • Read the Ethernet port line before the AV number. An AV600 kit on a 10/100 port stops at 100 Mbps no matter how good the wiring is.
  • Use the maker’s app or utility to see the powerline rate your pair actually reports, then take 20 to 30% of it. That is the figure to plan with.
  • Keep phone and laptop chargers out of the sockets right next to an adapter, and move the adapter away from motor-driven appliances if you can.
  • Buy the same series when you add an adapter. A slower one drags the whole network down to its rate.

What we would do

We would try powerline only where a cable run is not practical, and we would buy a kit with a gigabit Ethernet port. We would plug both adapters straight into wall sockets on the same circuit, pair them side by side, then move one to the far room and read the reported rate. If 20 to 30% of that figure covers what the room needs, we would keep it; if not, we would look at a mesh node or a cable before buying more adapters.

Questions people ask

Will a 1000 Mbps powerline kit give me 1000 Mbps? No. The maker says the box figure is the maximum rate at the physical layer, and that real throughput is typically 20 to 30% of the rate the adapters report. Even if a pair reported the full 1,000, that rule gives 200 to 300 Mbps.

Can I plug a powerline adapter into a power strip? The maker says not to. A power strip or surge protector can filter or block the powerline signal and cut the rate a lot. Plug each adapter straight into a wall socket.

Will powerline work through a UPS? Not through a UPS. The maker says a UPS usually filters the line and can cut the powerline connection. Plug the adapters into ordinary wall sockets, not the outlets on a UPS.

Do both adapters have to be on the same circuit? Yes. The setup guide says to plug the second adapter into a wall socket on the same electrical circuit. If a pair links side by side but loses the link in the other room, the maker says that usually means separate circuits.

Can I mix an AV600 adapter with an AV1000 kit? They are compatible, but the maker says the powerline rate drops to the slowest adapter's rate. An AV1000 and an AV600 together run at the AV600 rate, so buy the same series where you can.

How many powerline adapters can I add? It depends on the model. The maker's table gives limits from 6 to 64 adapters per network, and says most current models allow 16. In a mixed set, the model with the lowest limit sets it, and all adapters share one rate.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. TP-Link, TP-Link TL-PA7017 KIT (US): AV1000 gigabit powerline starter kit, specifications: Standards and Protocols HomePlug AV2, HomePlug AV, IEEE 1901, IEEE 802.3, IEEE 802.3u, IEEE 802.3ab Plug Type US Interface Gigabit Ethernet Port Button Pair/Reset button Max. Power Consumption Maximum: 2.7W (220V/50Hz) Typical: 2.3W (220V/50Hz) Standby: 0.5W (220V/50Hz) LED Power, Powerline, Ethernet Dimensions ( W x D x H ) 2.0 x 1.1 x 2.6 in (52 x 28.5 x 65 mm) Range Up to 300 meters/1000 feet over existing electrical wiring SOFTWARE FEATURES Modulation Technology OFDM (PLC) Encryption Powerline Security: 128-bit AES Encryption tp-link.com/us/home-networking/powerline/tl-pa7017-kit/
  2. TP-Link, TP-Link TL-PA7017 KIT (US): rate, compatibility and the physical-rate note: providing data transmissions of up to 1000 Mbps* over the electrical wiring for ranges up to 300 meters. tp-link.com/us/home-networking/powerline/tl-pa7017-kit/
  3. TP-Link, TP-Link TL-PA7017 KIT (US): compatibility and the physical-rate note: *Compatible with all HomePlug AV and AV2 Standard Powerline adapters. tp-link.com/us/home-networking/powerline/tl-pa7017-kit/
  4. TP-Link, TP-Link TL-PA7017 KIT (US): maximum powerline rates are physical rates: ***Maximum Powerline signal rates are the physical rates derived from HomeplugAV/AV2 specifications. Actual Powerline data throughput and Powerline range are not guaranteed and will vary as a result of network conditions and environmental factors, including electrical interference, volume of traffic and network overhead, AFCI circuit breaker, and Powerline being located in a separate circuit. tp-link.com/us/home-networking/powerline/tl-pa7017-kit/
  5. TP-Link, TP-Link TL-PA7017 KIT (US): plug and play, pair button: Connect a powerline adapter to the router, plug another powerline adapter into a wall socket in another room, and you're done! Pair for more security Press the "Pair" button on each adapter to create a more secure network. tp-link.com/us/home-networking/powerline/tl-pa7017-kit/
  6. TP-Link, TP-Link TL-PA4010 KIT (US): AV600 powerline starter kit, specifications: Standards and Protocols HomePlug AV2, IEEE802.3, IEEE802.3u Plug Type US Interface 1*10/100Mbps Ethernet Port Button Pair Button Max. Power Consumption Maximum: 2.5W Typical: 2.3W Standby: 0.36W tp-link.com/us/home-networking/powerline/tl-pa4010-kit/
  7. TP-Link, TP-Link TL-PA4010 KIT (US): AV600 rate: HomePlug AV2 standard compliant, high-speed data transfer rates of up to 600Mbps tp-link.com/us/home-networking/powerline/tl-pa4010-kit/
  8. TP-Link, TP-Link TL-PA4010 KIT (India): AV600 powerline starter kit, specifications: Standards and Protocols HomePlug AV, IEEE802.3, IEEE802.3u Interface 1*10/100Mbps Ethernet Port Button Pair Button Power Consumption Maximum: 4.60W (220V/50Hz) Typical: 4.26W (220V/50Hz) Standby: 0.88W (220V/50Hz) tp-link.com/in/home-networking/powerline/tl-pa4010-kit/
  9. TP-Link, TP-Link TL-PA4010 KIT (India): AV600 rate, sold in sets of two: HomePlug AV standard compliant, high-speed data transfer rates of up to 600Mbps tp-link.com/in/home-networking/powerline/tl-pa4010-kit/
  10. TP-Link, TP-Link TL-PA4010 KIT (India): adapters work in sets of two or more: Note: Powerline adapters must be deployed in sets of two or more. tp-link.com/in/home-networking/powerline/tl-pa4010-kit/
  11. TP-Link, TP-Link TL-WPA7517 KIT (India): AV1000 gigabit powerline Wi-Fi kit, specifications: Transmission Speeds Powerline: Up to 1000 Mbps Ethernet: 10/100/1000 Mbps Standards and Protocols HomePlug AV2, HomePlug AV, IEEE 1901, IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.11b/g/n (2.4GHz), IEEE 802.11a/n/ac (5GHz) Compatibility Compatible with all HomePlug AV & AV2 standard powerline adapters Plug Type EU Interface TL-WPA7517: 1 Ethernet Port TL-PA7017: 1 Ethernet Port Button Pair, Reset, Wi-Fi Clone, LED On/Off Max. Power Consumption TL-WPA7517: Maximum: 11W, Typical: 6.5W TL-PA7017: Maximum: 2.9W, Typical: 2.6W tp-link.com/in/home-networking/powerline/tl-wpa7517-kit/
  12. TP-Link, TP-Link TL-PA8010P KIT V3 user guide (US): plug and play, pairing: 3. Plug the other powerline adapter into a wall outlet on the same electrical circuit at the place you want internet. Wait until the powerline LED turns on. Note: If the Powerline LED does not turn on, reset each powerline adapter to its factory default settings. Refer to FAQ-Q2 for detailed information. 4. Connect your wired device, such as a computer or game console, to the powerline adapter via an Ethernet cable. Done! Now enjoy the internet! 3. Secure Your Powerline Networ k by Pairing All powerline adapters share some common factory settings, and can communicate with one another. If you want your powerline adapters to communicate only with your own powerline adapters, you should pair them. Thus a secured powerline network is formed and other powerline adapters can no longer join your powerline network without being paired. Note: You can only pair two devices at a time. tp-link.com/us/user-guides/tl-pa8010pkit_v3/chapter-2-powerl…
  13. TP-Link, TP-Link FAQ 2928 (US): powerline adapter speed vs actual speed: The speed shown on the box or product specification of a powerline adapter is the maximum powerline rate at the physical layer - not the actual throughput speed you will experience. For TP-Link powerline speeds, the actual conversion rate is typically 20-30% of the declared powerline rate, depending on your home's electrical wiring. tp-link.com/us/support/faq/2928/
  14. TP-Link, TP-Link FAQ 2928 (India): powerline adapter speed vs actual speed: For TP-Link powerline speeds, the actual conversion rate is typically 20-30% of the declared powerline rate, depending on your home's electrical wiring. tp-link.com/in/support/faq/2928/
  15. TP-Link, TP-Link FAQ 2928 (US): AV600 throughput capped by the 10/100 port: For AV600 powerline adapters, throughput is capped at 100 Mbps due to the 10/100 Mbps Ethernet port limitation. tp-link.com/us/support/faq/2928/
  16. TP-Link, TP-Link FAQ 2928 (US): the maker’s own worked example (364 Mbps powerline rate): The Powerline speed between the TL-WPA8630 and two TL-PA8010s was only up to 364 Mbps and 56 Mbps. However, the conversion rate (the ratio of the transmission rate to the powerline rate) is about 20%-30% (the actual conversion rate depends on the electrical wiring system). So the actual throughput should be about 73Mbps-109Mbps. tp-link.com/us/support/faq/2928/
  17. TP-Link, TP-Link FAQ 409 (US): slow powerline speed, four considerations: Powerline adapters should always be plugged directly into a wall outlet - using a power strip or surge protector can significantly reduce the powerline rate. Electrical devices with motors (air conditioners, washing machines, fans, kitchen appliances) can interfere with powerline signals. If possible, move the powerline adapter away from these devices, or plug the interfering devices into a surge protector. AC power adapters for phones, laptops, and similar devices can introduce noise on the power line, reducing powerline adapter performance. Keep AC power adapters away from powerline adapters. The maximum range of a powerline adapter is 300 meters, but interference and line quality can reduce the effective range. tp-link.com/us/support/faq/409/
  18. TP-Link, TP-Link FAQ 409 (India): slow powerline speed, four considerations: Power strips and surge protectors can filter or block the powerline signal, which significantly reduces the powerline rate. A direct wall-outlet connection provides the adapters with a cleaner signal path. tp-link.com/in/support/faq/409/
  19. TP-Link, TP-Link FAQ 406 (US): powerline questions, separate circuits: Can Powerline adapters work if they are separated by different electric circuits? A: No. If they can pair in the same room, but the powerline LED turns off when you move one powerline device to another area, this usually means they are plugged into separate electrical circuits, preventing them from communicating. Please try different locations. tp-link.com/us/support/faq/406/
  20. TP-Link, TP-Link FAQ 406 (US): powerline and a UPS: Can Powerline adapters work if they are separated by UPS? A: No. Usually, UPS has a filter function. It can cut the powerline connection. tp-link.com/us/support/faq/406/
  21. TP-Link, TP-Link FAQ 406 (India): powerline and a UPS: Can Powerline adapters work if they are separated by UPS? A: No. Usually, UPS has a filter function. It can cut the powerline connection. tp-link.com/in/support/faq/406/
  22. TP-Link, TP-Link FAQ 406 (US): adapters share the bandwidth: In the same private power line network, all devices share the whole bandwidth. tp-link.com/us/support/faq/406/
  23. TP-Link, TP-Link FAQ 406 (US): three-phase circuits and breaker boxes: Can TP-LINK powerline adapters work in different phases of the three-phase circuit? A: Yes, but its rate will be affected when crossing the phases. For a three-phase four-line circuit, we suggest you use the topology below to get good performance. Q3.10: Can Powerline adapters work if they are separated by Circuit Breakers/ Fuse Boxes/ Fuse Boards? A: Generally speaking, PLC can be used across Circuit Breakers/ Fuse Boxes/ Fuse Boards. A few Circuit Breakers/ Fuse Boxes/ Fuse Boards have a filtering effect and weaken the PLC communication. In most cases, they have little influence on the communication of PLC. tp-link.com/us/support/faq/406/
  24. TP-Link, TP-Link FAQ 3090 (US): are powerline adapters compatible with each other: TP-LINK AV500, AV600, AV1000, etc powerline adapters adopt HomePlug AV2 Standard, so they are compatible with each other. However, the powerline rate will drop to the lowest one's rate when using different AV adapters together, and in rare cases, it may cause unstable or pairing issues because of the low powerline rate. Therefore, to ensure good performance, we strongly recommend purchasing the same series of powerline products. tp-link.com/us/support/faq/3090/
  25. TP-Link, TP-Link FAQ 434 (US): how many powerline adapters on one network: Limits range from 6 to 64 nodes. In a mixed-model network, the maximum node count is determined by the model with the lowest limit. One node equals one single Powerline device. Most current TP-Link Powerline models support up to 16 nodes per network. tp-link.com/us/support/faq/434/

Author: Bulan Sarkar · Report an error

Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.