Will It Work? · Guide
Wi-Fi 6E and 6 GHz: why your device won’t connect
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
You have a router that says Wi-Fi 6E or Wi-Fi 7 on the box, and a phone or laptop that should use its 6 GHz band, but the device stays on 5 GHz or cannot see the 6 GHz network at all. This guide goes through what the 6 GHz band needs, using the router makers' and Apple's own support pages.
What the 6 GHz band needs
NETGEAR's answer to “what is required to use WiFi 6E” lists 3 things: a router, mesh system or access point that supports Wi-Fi 6E, a device that supports Wi-Fi 6E, and WPA3 security on the 6 GHz network (NETGEAR)(NETGEAR). The band came in with Wi-Fi 6E and is open only to devices that support Wi-Fi 6E or newer standards, Wi-Fi 7 included (NETGEAR). A 6 GHz router does nothing for a device without a 6 GHz radio: the device must also support 6 GHz Wi-Fi (NETGEAR), and Apple says the same from the other side, that a Wi-Fi 6E network needs a router or access point that supports Wi-Fi 6E (Apple).
The fourth check is the country, covered further down. Put together, the order to check is:
WPA3 is required on 6 GHz
On 2.4 and 5 GHz, WPA3 is the better choice. On 6 GHz it is the only one. NETGEAR says WPA3 security is mandatory for devices operating in the 6 GHz band, and that if the router is set to a different WPA version, devices cannot connect to 6 GHz (NETGEAR). TP-Link's Omada guide spells out the list: a 6 GHz network supports only Enhanced Open, WPA3-SAE and WPA3-Enterprise, and not WPA-PSK, WPA2-PSK or the other older modes (TP-Link). With WPA3 selected, Protected Management Frames (PMF) are set to mandatory and cannot be changed (TP-Link).
So a device can have a 6 GHz radio and still never use the band, if it cannot do WPA3. For what each security setting does on the other bands, see WPA2 vs WPA3.
One network name, or a separate one for 6 GHz
Apple says that for best performance with its devices, the router should use a single network name (SSID) across all its bands (Apple). If the names differ, an Apple device marks the network as having limited compatibility (Apple) and offers to join the 5 GHz network instead; say yes and it joins 5 GHz without some benefits of Wi-Fi 6E or Wi-Fi 7 (Apple). NETGEAR's usual advice matches: the same name and password on every band, with WPA3 on 6 GHz and WPA2/WPA3 on 2.4 and 5 GHz (NETGEAR).
TP-Link's guide for its business (Omada) access points takes the other side. Ticking 6 GHz on an existing network changes its security to WPA2-PSK/WPA3-SAE automatically (TP-Link). Some devices that once joined a network on WPA3 will not join it on WPA2 until the network is forgotten on the device (TP-Link), so it suggests separate names for 2.4/5 GHz and 6 GHz where possible (TP-Link). Both setups work. They suit different networks, and Apple and NETGEAR, writing about home networks, lean towards one name.
Older devices on a 6 GHz router
Under the one-name plan, nothing old is locked out. A WPA2-only device joins 2.4 or 5 GHz on WPA2, a Wi-Fi 6 device without a 6 GHz radio joins the same bands on WPA3, and only devices with Wi-Fi 6E or newer and WPA3 move up to 6 GHz.
The trouble cases are older devices and smart-home (IoT) gadgets that do not support WPA3 or PMF at all. TP-Link says some cannot join a network that has them switched on, even when PMF is only set to optional, and its fix is a separate network with 6 GHz turned off and WPA3 not set (TP-Link). On a home router, TP-Link suggests a separate guest network for older WPA2-only devices (TP-Link).
Range, channels and when to switch 6 GHz off
The 6 GHz band reaches less far than 5 GHz (NETGEAR). TP-Link puts it as weaker wall penetration and smaller coverage than 2.4 and 5 GHz (TP-Link). A device in a far room may be on 5 GHz simply because 6 GHz does not reach it.
Channel choice matters too. 6 GHz devices scan a group of preferred scanning channels (PSCs) instead of the whole band (NETGEAR), and some devices may not find a 6 GHz network on a non-PSC channel (TP-Link). If one device misbehaves on a single-name network, Apple devices let you turn off Wi-Fi 6E mode for that network, after which the device stops using its 6 GHz band (Apple).
Is 6 GHz Wi-Fi allowed where you live?
Not every country has opened the band, and not all of it. The Wi-Fi Alliance map shows two kinds of adoption: the lower part of the band and the full band (Wi-Fi Alliance)(Wi-Fi Alliance). Apple notes that 6 GHz features are not available in all regions (Apple).
For the differences between the three bands themselves, see 2.4, 5 and 6 GHz.
Tips and tricks
- Look for "6E" or "Wi-Fi 7" in your phone or laptop specs, not only "Wi-Fi 6". Plain Wi-Fi 6 devices have no 6 GHz radio.
- If the router lets you pick security per band, check that the 6 GHz line says WPA3. With anything else there, devices cannot join 6 GHz.
- Test 6 GHz in the same room as the router first. If it works there and not two rooms away, the problem is range, not settings.
- After changing names or security, forget the network on the device and join again, so it does not keep an old saved setting.
- Put a smart plug or old printer that refuses WPA3 on a guest network, instead of turning the main network down to WPA2.
What we would do
We would keep one network name and one password on every band, set WPA3 on 6 GHz and WPA2/WPA3 on 2.4 and 5 GHz, and leave the router on automatic channels. Then we would check the four things in Figure 1 for any device that never reaches 6 GHz. A device that still misbehaves gets Wi-Fi 6E mode turned off for that network, or a guest network if it cannot do WPA3.
If you are still choosing a router, the router upgrade checker shows whether a new one would help, and Wi-Fi 4 to Wi-Fi 7 explains what each generation adds.
Questions people ask
Why can’t my phone see the 6 GHz network? Check four things in order: that 6 GHz Wi-Fi is allowed where you live, that the router has a 6 GHz band, that the phone supports Wi-Fi 6E or newer, and that the 6 GHz network uses WPA3. A no at any step keeps the phone on 2.4 or 5 GHz.
Does 6 GHz Wi-Fi need WPA3? Yes. NETGEAR says WPA3 security is mandatory for devices operating in the 6 GHz band, and that devices cannot connect to 6 GHz if the router uses a different WPA version. TP-Link’s Omada guide lists only Enhanced Open, WPA3-SAE and WPA3-Enterprise for a 6 GHz network, not WPA2.
Can old WPA2 devices still use my Wi-Fi 6E router? Yes, on 2.4 or 5 GHz. With the router set to WPA2/WPA3 on those bands and WPA3 on 6 GHz, older devices join the lower bands and only devices with Wi-Fi 6E and WPA3 use 6 GHz.
Should the 6 GHz band have its own network name? For a home router, Apple and NETGEAR both recommend one name on every band, and Apple devices flag a network as having limited compatibility when the names differ. TP-Link’s guide for its business access points suggests separate names, because some devices that joined a name on WPA3 will not rejoin it on WPA2 until the network is forgotten.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- NETGEAR, NETGEAR KB 000064271: What is required to use WiFi 6E?:
To use this technology you require three things: A router, mesh system, or access point that supports WiFi 6E
kb.netgear.com/000064271/ - NETGEAR, NETGEAR KB 000064271: WPA3 on the 6 GHz network:
WPA3 security enabled on your 6 GHz network. This security standard is required on this band.
kb.netgear.com/000064271/ - NETGEAR, NETGEAR KB 000064415: Why can't my device detect the 6 GHz wireless band?:
The 6 GHz wireless band was introduced with the WiFi 6E standard and is exclusive to devices that support WiFi 6E and newer standards, including WiFi 7 and successive future WiFi versions.
kb.netgear.com/000064415/ - NETGEAR, NETGEAR KB 000064415: the device must support 6 GHz:
Your client device must also support 6 GHz WiFi.
kb.netgear.com/000064415/ - NETGEAR, NETGEAR KB 000064415: WPA3 is mandatory on 6 GHz:
WPA3 security is mandatory for devices operating in the 6 GHz wireless band. If your router, mesh system, or access point is set up to use a different WPA security version, devices cannot connect to the 6 GHz band.
kb.netgear.com/000064415/ - NETGEAR, NETGEAR KB 000064415: one name, WPA3 on 6 GHz, WPA2/WPA3 on 2.4 and 5 GHz:
We typically recommend that you use the same WiFi network name (SSID) and password for all WiFi bands on your router, with WPA3-PSK security for the 6 GHz band and WPA2/WPA3-PSK security for the 2.4 GHz and 5 GHz bands.
kb.netgear.com/000064415/ - NETGEAR, NETGEAR KB 000064415: preferred scanning channels:
Instead of scanning the entire 6 GHz spectrum for an optimal channel, 6 GHz WiFi devices scan PSCs for efficient connectivity.
kb.netgear.com/000064415/ - NETGEAR, NETGEAR KB 000064415: 6 GHz range:
The 6 GHz band has a shorter range than the 5 GHz band.
kb.netgear.com/000064415/ - TP-Link, TP-Link Omada Support 13253: Getting started with 6GHz (security modes):
Currently, 6GHz SSID only supports Enhanced Open / WPA3-SAE / WPA3-Enterprise security modes, not PPSK / WPA-PSK / WPA2-PSK / WPA-Enterprise / WPA2-Enterprise
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: PMF on 6 GHz:
When WPA3-SAE and WPA3-Enterprise are selected, the PMF will be set to Mandatory and no change is allowed.
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: one SSID across bands:
when 6GHz is ticked, it will be automatically changed to WPA2-PSK/WPA3-SAE regardless of which WPA mode was previously selected
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: WPA3 then WPA2 on one SSID:
they will not be able to connect to a SSID with WPA2 encryption if they connected to it with WPA3 encryption before, unless they manually delete/forget that SSID on the client side and re-associate with the SSID
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: separate SSIDs:
please create different SSIDs for 2.4GHz/5GHz and 6GHz as much as possible
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: legacy and IoT clients:
Some legacy clients or IOT devices do not support WPA3 or PMF (Protect Management Frames), even if PMF is set to Disable or Capable in Controller, they still cannot connect to the relevant SSID. For this case, please create a separate SSID (with 6GHz turned off and WPA3 not set) for them.
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: 6 GHz coverage:
Compared with 2.4GHz/5GHz, 6GHz band has weaker ability to penetrate wall and smaller wireless coverage area.
support.omadanetworks.com/us/document/13253/ - TP-Link, TP-Link Omada Support 13253: non-PSC channels:
Some clients may not discover 6GHz networks using Non-PSC channels.
support.omadanetworks.com/us/document/13253/ - Apple, Apple Support 102285: Use Wi-Fi 6E or Wi-Fi 7 networks with Apple devices:
To create a Wi-Fi 6E network, you need a Wi-Fi router or access point that supports Wi-Fi 6E.
support.apple.com/en-us/102285 - Apple, Apple Support 102285: one network name across all bands:
the Wi-Fi router providing the network should use a single network name (SSID) across all of its Wi-Fi bands
support.apple.com/en-us/102285 - Apple, Apple Support 102285: limited compatibility:
If the router isn't using the same name for all three bands, your device identifies the network as having limited compatibility.
support.apple.com/en-us/102285 - Apple, Apple Support 102285: joining the 5 GHz network instead:
If you select OK or Join, your device joins the 5 GHz network without some benefits of Wi-Fi 6E or Wi-Fi 7.
support.apple.com/en-us/102285 - Apple, Apple Support 102285: Wi-Fi 6E mode off:
you can turn off Wi-Fi 6E mode when connected to that network. Your device will then no longer use that network's 6 GHz band.
support.apple.com/en-us/102285 - Apple, Apple Support 102285: regions:
Wi-Fi 6E and Wi-Fi 7 features that operate on the 6 GHz band are not available in all regions.
support.apple.com/en-us/102285 - Wi-Fi Alliance, Wi-Fi Alliance: Regulations enabling 6 GHz Wi-Fi (country map):
Adopted 5925/5945-6425 MHz Adopted 5925-7125 MHz
wi-fi.org/regulations-enabling-6-ghz-wi-fi - Wi-Fi Alliance, Wi-Fi Alliance: Regulations enabling 6 GHz Wi-Fi (country map):
Australia 5925/5945-6425 MHz ... Canada 5925-7125 MHz ... Germany 5925/5945-6425 MHz ... India 5925/5945-6425 MHz ... Japan 5925/5945-6425 MHz ... Saudi Arabia 5925-7125 MHz ... Singapore 5925/5945-6425 MHz ... South Africa 5925/5945-6425 MHz ... South Korea 5925-7125 MHz ... United Arab Emirates 5925/5945-6425 MHz ... United Kingdom 5925/5945-6425 MHz ... United States 5925-7125 MHz
wi-fi.org/regulations-enabling-6-ghz-wi-fi - TP-Link, TP-Link blog 2556: WPA2 vs. WPA3 (guest network):
You can also consider putting older WPA2-only devices on a separate guest network, which adds a layer of separation between them and your primary devices.
tp-link.com/us/blog/2556/wpa2-vs-wpa3-a-breakdown-of-wi-fi-s…