Will It Work? · Guide
Home Ethernet switch: ports, speeds and managed or not
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
Most home routers have four LAN ports, and a TV, a games console, a computer and network storage fill them fast. A small Ethernet switch adds more. The port counts, switch types and link speeds below come from a router maker's switch guide and the spec pages of three switches and two routers.
How many ports a switch adds
A switch connects to the router with one cable, which takes one port at each end. The US and India routers we checked both list four gigabit LAN ports (TP-Link)(TP-Link), and the US and India 5-port switches list five gigabit ports (TP-Link)(TP-Link). Put together, that is (4 − 1) + (5 − 1) = 7 free ports, 3 more than the router alone.
An 8-port switch on the same router gives 10. Count the wired devices you have now, add one or two for later, and pick the port count from that.
Unmanaged, smart or managed
TP-Link's guide to its own switch range sorts them into five kinds. An unmanaged switch has no configuration interface or options at all: you plug devices in, and if you only need more Ethernet ports, it says this is the right switch (TP-Link). Both 5-port gigabit switches above say plug and play, no configuration (TP-Link)(TP-Link).
An easy smart switch adds a utility or web page for basic settings such as VLANs, QoS, link aggregation, IGMP snooping and port mirroring, and the guide says these turn up in homes and small offices (TP-Link). A smart switch adds Telnet, SSH and SNMP management, access lists and Spanning Tree (TP-Link). L2 managed switches add a console port for a command line (TP-Link), and L3 managed switches add routing, like a router (TP-Link).
Port speeds: each link settles on its own
Each port senses the speed of the device on it and adjusts (TP-Link). On a gigabit switch that means 10, 100 or 1000 Mbps (TP-Link), and the two ends agree on the highest speed both support (Apple). So an older device with a 100 Mbps port links at 100, and a computer with a 2.5 gigabit port links at 1 gigabit on a gigabit switch.
A 2.5 gigabit switch has a third speed. The US model we checked lists five ports at 100 Mbps, 1 Gbps or 2.5 Gbps and IEEE 802.3bz (TP-Link), with three-speed auto-negotiation (TP-Link). For 2.5 gigabit over a cable run, IEEE 802.3bz uses Category 5e for up to 100 metres (Fluke Networks). To check a cable and port pair, use the Ethernet port and cable checker.
The link to the router is shared
Two devices on the same switch talk through the switch, at the speed of their own links. Anything going to the router, or out to the internet, crosses the one link between the switch and the router. With 2.5 gigabit devices on a 2.5 gigabit switch, the path between them is 2,500 Mbps; the path to a gigabit router port is 1,000 Mbps.
The 2.5 gigabit switch lists a switching capacity of 25 Gbps (TP-Link). Its five ports add up to 12.5 Gbps, so the figure on the page is twice that. For the speed your devices can reach through the router, see box speed vs internet speed.
Power: a few watts on the label
A small switch draws little. The US 5-port gigabit switch lists a maximum of 3 W (TP-Link), the India one 2.49 W (TP-Link), and the 2.5 gigabit one 12.11 W (TP-Link). If the switch is on a backup battery with the router in a power cut, add its figure to the total in the power-cut backup calculator.
A switch that powers cameras or access points over the cable is a PoE switch, with its own budget; see PoE explained.
Tips and tricks
- Count the router’s LAN ports first. A switch takes one of them, and one of its own ports, for the link between the two.
- For more ports at home, an unmanaged switch is enough. Smart and managed switches are for networks that need VLANs, remote management or routing.
- A 2.5 gigabit switch only helps between 2.5 gigabit devices. Check the Ethernet line on each device’s spec page before paying for it.
- If the switch will share a backup battery with the router in a power cut, read the maximum power line on its spec page and add it to the total.
- Put the switch near the devices it serves, so one cable runs back to the router instead of one per device.
What we would do
We would buy an unmanaged switch with a few more ports than we need today, at the speed of the router's LAN ports. With a gigabit router, a gigabit switch is the match. A 2.5 gigabit switch makes sense when two or more devices on it have 2.5 gigabit ports and move large files between them, or when the router has a 2.5 gigabit LAN port. We would skip smart and managed switches unless we had a setting in mind that needed one.
Questions people ask
Do I need a managed switch at home? Usually not. TP-Link’s switch guide says that if you only need more Ethernet ports and no Layer 2 features, an unmanaged switch is the right one. It has no settings: you plug devices in and it works.
Will a switch slow down my internet? Not below your router’s own port. A gigabit switch on a gigabit router port links at 1,000 Mbps, which is the router port’s speed anyway. Everything going to the internet still shares that one link to the router.
Is a 2.5 gigabit switch worth it? Only for traffic between 2.5 gigabit devices on the switch, such as a computer and network storage. Traffic to the router goes through the router’s LAN port; on a gigabit port that path is 1,000 Mbps.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- TP-Link, Omada (TP-Link) KB 12901: unmanaged switch:
You are not able to configure the unmanaged switch because it doesn’t support any configuration interface or options. It is plug-and-play, so you only need to connect your computer or other network devices to the unmanaged switch directly. Therefore, if you do not need any L2 features, but only need to extend the number of Ethernet ports, unmanaged switch is the right switch for you.
support.omadanetworks.com/us/document/12901/ - TP-Link, Omada (TP-Link) KB 12901: easy smart switch:
You can use Utility or Web interface to manage easy smart switch and configure basic settings, such as VLAN, QoS and a few L2 features like LAG, IGMP Snooping and Port Mirroring. If there are no advanced applications needed, easy smart switch should be the best choice for you. Normally, easy smart switch will be found in the home, SOHO or small business.
support.omadanetworks.com/us/document/12901/ - TP-Link, Omada (TP-Link) KB 12901: smart switch:
Smart switch can be managed by Web interface, Telnet, SSH and SNMP. It supports far more L2 features and better QoS than easy smart switch, additionally, smart switch supports more advanced functions like ACL and Spanning Tree protocol
support.omadanetworks.com/us/document/12901/ - TP-Link, Omada (TP-Link) KB 12901: L2 managed switch:
L2 managed switch has a console port for CLI (Command Line Interface), it has all the managing ways and advanced features that smart switch has
support.omadanetworks.com/us/document/12901/ - TP-Link, Omada (TP-Link) KB 12901: L3 managed switch:
Layer 3 switch has some L3 functions just like a traditional router--static routing, routing protocol like OSPF and ECMP, multicast routing protocol and DHCP relay.
support.omadanetworks.com/us/document/12901/ - TP-Link, TP-Link TL-SG105 (US): 5-port gigabit unmanaged switch, overview:
5× 10/100/1000 Mbps Auto-Negotiation RJ45 ports supporting Auto-MDI/MDIX Plug and play, no configuration needed
tp-link.com/us/business-networking/soho-switch-unmanaged/tl-… - TP-Link, TP-Link TL-SG105 (US): specifications:
Interface 5× 10/100/1000 Mbps, Auto-Negotiation, Auto-MDI/MDIX Ports ... Max. Power Consumption 3.0 W (220 V/ 50 Hz) ... IGMP Snooping Loop Prevention
tp-link.com/us/business-networking/soho-switch-unmanaged/tl-… - TP-Link, TP-Link TL-SG105 (US): auto-negotiation:
Auto-negotiation on each port senses the link speed of a network device and intelligently adjusts to ensure full compatibility and optimal performance.
tp-link.com/us/business-networking/soho-switch-unmanaged/tl-… - TP-Link, TP-Link TL-SG1005D (India): 5-port gigabit desktop switch, specifications:
Interface 5 10/100/1000Mbps RJ45 Ports AUTO Negotiation/AUTO MDI/MDIX ... Max. Power Consumption 2.49W (220V/50Hz) ... Plug and play, no configuration required
tp-link.com/in/home-networking/soho-switch/tl-sg1005d/ - TP-Link, TP-Link TL-SG1005D (India): auto-negotiation:
Auto-negotiation on each port senses the link speed of a network device (either 10, 100, or 1000 Mbps) and intelligently adjusts for compatibility and optimal performance.
tp-link.com/in/home-networking/soho-switch/tl-sg1005d/ - TP-Link, TP-Link TL-SG105-M2 (US): 5-port 2.5G desktop switch, specifications:
Standards and Protocols IEEE 802.3, 802.3u, 802.3ab, 802.3x, 802.1p, 802.3bz Interface 5× 100Mbps/1Gbps/2.5Gbp Ports, Auto-Negotiation, Auto-MDI/MDIX ... Max. Power Consumption 12.11 W ... Switching Capacity 25 Gbps
tp-link.com/us/business-networking/unmanaged-switch/tl-sg105… - TP-Link, TP-Link TL-SG105-M2 (US): three-speed auto-negotiation:
Auto-negotiation 3-speed (100Mb/1G/2.5G) connections sense the link speeds and intelligently adjust for compatibility and optimal performance for all your devices
tp-link.com/us/business-networking/unmanaged-switch/tl-sg105… - Apple, Apple Support: About the 10 Gigabit Ethernet port on Mac (Mac User Guide):
Depending on the device you’re connecting to, the cable type and technology used, and the cable length, the highest link speed is automatically negotiated. For example, if the device you’re connecting to is 10 Gbit/s-capable and the cable can support the speed, the two devices would negotiate the 10 Gbit/s speed.
support.apple.com/guide/mac-help/mchlcef4be50/mac - TP-Link, TP-Link Archer AX55 (US): Ethernet ports and speed note, specifications:
Ethernet Ports 1× Gigabit WAN Port 4× Gigabit LAN Ports ... Actual network speed may be limited by the rate of the product's Ethernet WAN or LAN port
tp-link.com/us/home-networking/wifi-router/archer-ax55/ - TP-Link, TP-Link Archer AX23 (India): Ethernet ports, specifications:
Ethernet Ports 1× Gigabit WAN Port 4× Gigabit LAN Ports
tp-link.com/in/home-networking/wifi-router/archer-ax23/ - Fluke Networks, Fluke Networks blog: Will My Existing Cable Plant Support 2.5/5GBASE-T? (17 Jan 2018):
IEEE 802.3bz specifies 2.5 Gbps over 100 meters of Category 5e cabling or 5 Gbps over 100 meters of Category 6 cabling. It also includes support for 5 Gbps over Category 5e on defined use cases (extended frequencies).
flukenetworks.com/blog/cabling-chronicles/will-my-existing-c…