Will It Work? · Guide
Wi-Fi calling at home: phone checks and router settings that block it
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
Wi-Fi calling sends ordinary phone calls over your internet line when the mobile signal indoors is weak. When it works on a friend's Wi-Fi but not on yours, the cause is usually something on your router. This guide sorts phone, carrier and network problems apart, then goes through the router settings one maker lists for Wi-Fi calling, in its order. It names no carriers, because which ones offer the feature differs by country and plan.
First check that the Wi-Fi calling option exists in the phone's settings; if it does not, the carrier does not offer it on that phone. Then try another Wi-Fi network. If calls work there, fix the home router: update the firmware, turn SIP ALG off, reserve an address for the phone, and only if it still fails, open UDP 500 and 4500 to that address.
How a Wi-Fi call reaches the carrier
A phone maker describes the feature simply: when you have Wi-Fi but little or no mobile coverage, the phone can make and receive voice calls over the Wi-Fi (Apple). The phone builds a secured tunnel across your router and the internet to the carrier. That tunnel is set up with the IKE protocol, which runs over UDP ports 500 and 4500 (IETF). Your router is the only part of that path you control.
Phone, carrier or network?
If the phone's settings show no Wi-Fi calling option, one maker says the carrier does not support the feature (Google), and no router setting will change that. Not all carriers offer it, and some may charge for it, so the carrier is the place to ask (Google).
If the option is there, take the phone to a different Wi-Fi network. Another maker's troubleshooting includes exactly that step, because not all Wi-Fi networks work with Wi-Fi calling (Apple). Working elsewhere and failing at home points to your router; failing everywhere points back to the phone or the carrier.
Phone checks first
- Check that your carrier offers Wi-Fi calling and that the option shows in the phone’s settings.
- Turn Wi-Fi calling on and enter or confirm the emergency address if asked.
- Restart the phone.
- Try a different Wi-Fi network to see whether the problem follows the phone or your network.
- Turn Wi-Fi calling off and on again.
One maker asks you to wait two minutes between these steps (Apple), so working through all five takes about 8 minutes of waiting. When you turn the feature on you may be asked for an address for emergency services; the same maker says the phone uses mobile service for emergency calls whenever it is available (Apple). On another maker's phones, Wi-Fi calling switches itself off when the phone detects a problem and stays off until it is fixed (Google), so check the switch again after any change.
Router settings that block it
One router maker's Wi-Fi calling FAQ starts by asking you to confirm that the provider offers Wi-Fi calling and that the phone shows the option, and then gives five router steps in this order (TP-Link):
- Update the router firmware.
- Turn SIP ALG off (Advanced > NAT Forwarding).
- Reserve an address for the phone.
- Forward UDP 500 and 4500 to the phone’s reserved address.
- Add port trigger entries for UDP 500 and 4500.
On the same maker's mesh systems, the SIP ALG switch sits in the app under More > Advanced > NAT Forwarding > SIP ALG (TP-Link). Other makers put it under names such as NAT, firewall or WAN settings; the router's manual names the page. The firmware update guide and the address reservation guide cover steps 1 and 3.
SIP ALG, and why it gets in the way
SIP ALG is a router feature that helps internet-phone (VoIP) apps and devices get through the router's firewall, and most routers turn it on for that reason. The same maker says some apps and devices now handle the firewall themselves, and that this may conflict with SIP ALG; turning it off lets their calls work normally (TP-Link). The same maker's Wi-Fi calling fix turns it off as step 2 (TP-Link).
UDP 500 and 4500
Steps 4 and 5 of the router maker's list forward UDP 500 (IKE) and UDP 4500 (IPsec NAT traversal) to the phone's reserved address and add port-trigger entries for the same two ports (TP-Link). Those are the ports the tunnel is set up on (IETF). A forwarded port stays open to that one address until you remove the rule, so try steps 1 to 3 first, and delete the rules again if calling still fails with them in place. The port forwarding guide and the port triggering guide show where both settings live.
Tips and tricks
- Test on a second Wi-Fi network before touching the router; it tells you whether the router is involved at all.
- No Wi-Fi calling switch in the phone settings means the carrier does not offer it there; no router change will add it.
- Turn SIP ALG off before opening ports: it is the router maker’s step 2, and it opens nothing.
- Reserve the phone’s address before any port rule, or the rule may point at the wrong device after a restart.
- If the phone uses a rotating private Wi-Fi address, set it to fixed or off for the home network before reserving; the reservation guide shows why.
- Check the Wi-Fi calling switch again after each change; one maker’s phones turn it off by themselves after a problem.
What we would do
We would first confirm the switch is in the phone's settings and that calls work on another Wi-Fi network. If they do, we would update the router firmware and turn SIP ALG off, then test again. We would reserve the phone's address next, and add the UDP 500/4500 rules only if calls still fail, removing them if they make no difference.
Questions people ask
Why does Wi-Fi calling work at work but not at home? Then the phone and the carrier are fine and your home network is the place to look. Not every Wi-Fi network works with Wi-Fi calling, according to one phone maker. On the router, one maker’s order is: update the firmware, turn SIP ALG off, reserve an address for the phone, and only then open UDP ports 500 and 4500.
Should I turn SIP ALG off for Wi-Fi calling? One router maker lists it as step 2 of its Wi-Fi calling fix. SIP ALG is on in most routers to help internet-phone (VoIP) apps and devices through the firewall, and the same maker says it may conflict with apps and devices that handle the firewall themselves.
Which ports does Wi-Fi calling use? The secured tunnel the phone builds to the carrier is set up with IKE, which runs over UDP ports 500 and 4500 (IETF RFC 7296). That is why one router maker’s Wi-Fi calling fix ends with forwarding and port-trigger entries for those two ports.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- TP-Link, TP-Link FAQ 1259 (US): Wi-Fi calling through a TP-Link router:
Make sure your Internet Service Provider provides you with Wi-Fi calling service and the Phone has Wi-Fi calling option available in settings. … Step 1. Check if you are running the latest Firmware for the TP-Link router. … Step 2. Disable SIP ALG. On the wireless router, You may go to Advanced > NAT Forwarding > Uncheck " Enable SIP ALG " > click on Save . … Step 3. Reserve the IP Address for the Smartphone on the TP-Link router. … Step 4. Enable Port forwarding for UDP port 500 (IKE2) and port 4500 (IPsec Nat Traversal). … Step 5. Enable Port Trigger entries for UDP port 500 (IKE2) and port 4500 (IPsec Nat Traversal).
tp-link.com/us/support/faq/1259/ - TP-Link, TP-Link FAQ 2422: what SIP ALG does and turning it off on Deco:
SIP ALG is a feature that helps VoIP applications or devices go through the router firewall to make VoIP calls smoothly. Therefore, most routers will enable the SIP ALG feature to be compatible with VoIP applications or devices. However, some VoIP applications or devices have added support for firewall penetration, which may conflict with the SIP ALG feature. … More -> Advanced -> NAT Forwarding -> SIP ALG
tp-link.com/us/support/faq/2422/ - Apple, Apple Support 108066: Make a call with Wi-Fi Calling:
If you have a Wi-Fi connection in an area with little or no cellular coverage, use Wi-Fi Calling to make or receive a voice phone call. … You might need to enter or confirm your address for emergency services. … When cellular service is available, your iPhone uses it for emergency calls. … Wait two minutes before you go from one step to the next. … Connect to a different Wi-Fi network. Not all Wi-Fi networks work with Wi-Fi Calling. Turn Wi-Fi Calling off and then on again.
support.apple.com/en-us/108066 - Google, Google Phone app Help 2811843: Make calls over Wi-Fi:
Not all carriers support calls over Wi-Fi. … You may incur additional charges for making calls over Wi-Fi, so check with your mobile service provider for details. … If you don't find this option, your carrier doesn’t support this feature. … If your phone detects Wi-Fi calling issues, it turns off Wi-Fi calling until the problem is fixed. … When you're not connected to Wi-Fi, your calls will use your mobile carrier, if you have one.
support.google.com/phoneapp/answer/2811843?hl=en - IETF, IETF RFC 7296: Internet Key Exchange Protocol Version 2 (IKEv2), section 2 and 3.1:
IKE normally listens and sends on UDP port 500, though IKE messages may also be received on UDP port 4500 with a slightly different format … IKE runs over UDP ports 500 and 4500
rfc-editor.org/rfc/rfc7296