Will It Work? · Checker
Will your router carry your full internet plan?
By Bulan Sarkar, founder of ElectronicsInfoline (since 2000)
A new router only helps if the old one is what slows you down. Type your plan speed, pick your router or type its figures, and the checker follows the path from the plan to your device, over Wi-Fi and over a cable, to find the slowest hop. Every router figure comes from the maker's spec page, with India and US models kept apart.
Your router holds the plan back when its WAN port is slower than the plan: a 10/100 port caps every device at 100 Mbps, and a gigabit port at 1,000 Mbps. Over Wi-Fi, the router's figure for your band is a second cap. If both are at or above the plan, the router is not the limit, and a new one will not make the internet faster.
1. Your internet plan
From your bill or the provider’s plan page. 1 Gbps = 1000 Mbps.
2. Your router
Models come from the maker’s own spec page; India and US pages are kept apart, because the same name can be a different model.
The per-band line on the spec page, such as “5 GHz: 867 Mbps”, not the AC1200 or AX3000 on the box.
3. The device you care about
Phones and laptops show the band in their Wi-Fi details.
Shown as link speed or Tx rate in the device’s Wi-Fi details.
With limitsWired gets your plan; Wi-Fi on 5 GHz tops out below it
The router's 5 GHz figure (867 Mbps) is the most it links at on that band, and it is below your 1000 Mbps plan. A router with a higher figure for the band your device uses would raise that ceiling, if the device's own Wi-Fi links that fast too.
Over Wi-Fi: at most 867 Mbps (108.4 MB/s in a download manager). Wired: at most 1 Gbps.
Figures for TP-Link Archer C6 (India spec page). Change any field to use your own.
Show the working
- Wi-Fi path: Internet plan 1 Gbps → Router WAN port 1 Gbps → Router Wi-Fi, 5 GHz 867 Mbps. Slowest: Router Wi-Fi, 5 GHz, 867 Mbps (108 MB/s).
- Wired path: Internet plan 1 Gbps → Router WAN port 1 Gbps → Router LAN port 1 Gbps. Slowest: Internet plan, 1 Gbps (125 MB/s).
- Wi-Fi figure 867 Mbps < plan 1000 Mbps: the router's Wi-Fi on this band is the limit for one device.
Speeds are link rates and port rates, the most each hop can carry. Real downloads often come in lower; nothing here is measured. The provider's own box and the cable to it can cap the speed too.
The speed is set by the slowest hop
Internet comes in through the plan, then the router's WAN port, then either a LAN port and a cable or the Wi-Fi link to your device. TP-Link says the speed you get is limited by the slowest point in that path (TP-Link). The router's own spec pages add that the real speed may be limited by the rate of its WAN or LAN port (TP-Link).
So the checker works out two ceilings: one for a device on Wi-Fi and one for a device on a cable. Whichever hop is lowest on each path sets the most that device can get. Real downloads are often below that ceiling (TP-Link), but no router can lift a ceiling set by the plan.
The WAN port: the cap for every device
The WAN port is where the cable from the provider's box plugs in. TP-Link: a router with a 100 Mbps WAN port cannot deliver more than 100 Mbps of internet speed, whatever its wireless rate. Its example router links at 450 Mbps on 2.4 GHz and 867 Mbps on 5 GHz, and its devices still get 100 Mbps at most (TP-Link).
The same page says a Fast Ethernet port tops out at 100 Mbps and a Gigabit port at 1000 Mbps, and recommends a gigabit WAN port once the plan is above 100 Mbps (TP-Link). Faster plans follow the same rule, and Figure 3 gives the slowest WAN port that passes each range of plans.
The Wi-Fi figure: a second cap, and only a maximum
Spec pages give one figure per band, such as “5 GHz: 867 Mbps” on an AC1200 router (TP-Link). TP-Link calls this the signal rate: the maximum wireless link speed the router can provide, and not the internet speed from your provider (TP-Link). A device on that band can't link faster than that figure, so it is a cap like the WAN port.
It is also only a maximum. The link a device gets is negotiated from the wireless mode, the distance and the noise; TP-Link's example is a 325 Mbps link on a router rated 1300 Mbps on 5 GHz (TP-Link). That is why the checker asks for the link speed your device shows. With it, the result uses the real link instead of the router's best case.
Use the per-band line, not the class on the box. AC1200 is 867 Mbps on 5 GHz plus 300 Mbps on 2.4 GHz, and one device uses one band at a time. The box speed vs internet speed guide explains the class names.
Six routers from maker spec pages
The model picker holds three India and three US routers, each taken from its own market's spec page: a 10/100 N300 model, a gigabit AC1200, a gigabit AX1800, a gigabit AX3000, an AX6000 with one 2.5 Gbps WAN/LAN port, and a BE9300 with a 2.5 Gbps WAN port and 2.5 Gbps LAN ports.
The figure shows why the WAN port comes first. The 10/100 model links at 300 Mbps over Wi-Fi but passes 100 Mbps of internet at most, and every gigabit model is capped at 1,000 Mbps whatever its Wi-Fi figure. On the AX6000, using the 2.5 Gbps port as the WAN leaves one gigabit WAN/LAN port and three gigabit LAN ports for wired devices (TP-Link).
Worked examples
India: a 300 Mbps plan on an N300 router with 10/100 ports
No device, wired or Wi-Fi, gets more than 100 Mbps through this router. For the whole plan, the new router needs a WAN port of 1 Gbps or faster.
Result: no. Wi-Fi and wired both stop at 100 Mbps; a router with a gigabit WAN port moves the limit back to the plan.
India: a 1 Gbps plan on an AC1200 router with gigabit ports
The router's 5 GHz figure (867 Mbps) is the most it links at on that band, and it is below your 1000 Mbps plan. A router with a higher figure for the band your device uses would raise that ceiling, if the device's own Wi-Fi links that fast too.
Result: with limits. A wired computer can get 1 Gbps; one device on 5 GHz gets 867 Mbps at most.
US: a 2 Gbps plan on an AX6000 router and on a BE9300 router
The AX6000's 2.5 Gbps WAN port and its 4804 Mbps on 5 GHz both clear the plan, so the router does not cap Wi-Fi below it. Its other ports are gigabit, so a wired computer gets 1 Gbps at most. The BE9300 has 2.5 Gbps LAN ports as well, so a wired computer with a 2.5 Gbps port can get the full 2 Gbps.
Result: yes for both over Wi-Fi; for wired devices, only the BE9300 passes the whole plan.
Tips and tricks
- Find the WAN port line on the spec page before anything else. A router with a 10/100 WAN port caps every device at 100 Mbps, so its Wi-Fi figures don’t matter for internet speed.
- Run a speed test on a computer plugged into the router. If the wired result reaches the plan and Wi-Fi does not, the Wi-Fi link is your slowest hop, not the plan or the WAN port.
- Read the link speed in your phone or laptop’s Wi-Fi details and type it into the checker. It is the real figure for that spot in the house, and often below the router’s maximum.
- For a plan above 1 Gbps, check the provider’s box too. Its LAN port and the cable to the router are hops in the same path; the Ethernet cable checker covers both.
- Divide by 8 before you compare a download manager with your plan. A 1,000 Mbps ceiling shows up as 125 MB/s at most.
What we would do
If the WAN port is slower than the plan, we would replace the router; that is the one case where a new router is sure to raise the ceiling. For plans up to 1,000 Mbps, a gigabit WAN port is enough, and we would look for a 2.5 Gbps one only when the plan goes above that. If the WAN port is fine but Wi-Fi falls short, we would check the link speed on the device first. The link is set partly by distance, so a device far from the router can gain from a better spot or from a mesh node or access point nearby; a new router in the same place may not change it.
If every hop is at or above the plan, we would keep the router. To see the cable side, use the Ethernet cable checker; for the Wi-Fi side, read Wi-Fi generations explained and mesh, extender or access point.
Questions people ask
Why do I get only 100 Mbps on a faster plan? Check the router's WAN port. TP-Link puts it plainly: a router with a 100 Mbps WAN port cannot deliver more than 100 Mbps of internet speed, whatever its wireless rate. A port listed as 10/100 or Fast Ethernet is that kind. A router with a gigabit WAN port lifts the cap to 1,000 Mbps.
Do I need a new router for a 1 Gbps plan? For wired devices, a gigabit WAN port and gigabit LAN ports are enough. Over Wi-Fi, look at the router’s figure for the band your device uses. If it is below 1,000 Mbps, as the 867 Mbps on the AC1200 model here is, one device can’t link at the full plan on that band.
Will a Wi-Fi 6 or Wi-Fi 7 router make my internet faster? Only if the old router was the slowest hop. If the plan is slower than the router’s WAN port and its Wi-Fi figure, the plan sets the speed and a new router will not raise it. Put your plan and router into the checker to see which hop sets the limit.
What is the WAN port on a router? It is the port the cable from your provider’s box plugs into. Its rate on the spec page, such as 10/100 Mbps, Gigabit or 2.5 Gbps, is the most internet speed any device can get through the router.
My router says 867 Mbps on 5 GHz. Why does my phone show less? That figure is the most the router links at on that band. TP-Link says the link speed is negotiated based on wireless mode, distance and noise, and its own example shows a 325 Mbps link on a router rated 1300 Mbps on 5 GHz. Type the link speed your phone shows into the checker to use the real figure.
Sources
Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.
- TP-Link, TP-Link FAQ 2435: TP-Link Router Internet Speed FAQs: Mbps, Link Speed, and Wi-Fi Explained (last updated 10 Jun 2026):
A router with a 100Mbps WAN port cannot deliver more than 100Mbps of internet speed, regardless of its wireless signal rate. ... This is why even though the negotiating speed between wireless clients and the router can get 450Mbps(2.4GHz) or 867Mbps(5GHz), the download or upload speed of the devices is still 100Mbps at most. ... Fast Ethernet Port means the maximum speed is 100Mbps; Gigabit Ethernet Port means the maximum speed is 1000Mbps. ... A router with a Gigabit WAN port is recommended if your ISP plan exceeds 100Mbps.
tp-link.com/us/support/faq/2435/ - TP-Link, TP-Link FAQ 2435: TP-Link Router Internet Speed FAQs: Mbps, Link Speed, and Wi-Fi Explained (last updated 10 Jun 2026):
Internet speed is limited by the slowest point in the network path, including the ISP connection, WAN port capability, and the type of cable or adapter used. ... The internet speed is mainly limited by the lowest speed in the network path. There are many factors which will affect the network speed in the network path, such as ISP, interferences, server stability, surroundings, and more. ... Due to network fluctuations and line disturbances in the actual speed measurement, we recommend performing multiple tests to obtain accurate results.
tp-link.com/us/support/faq/2435/ - TP-Link, TP-Link FAQ 2435: TP-Link Router Internet Speed FAQs: Mbps, Link Speed, and Wi-Fi Explained (last updated 10 Jun 2026):
Signal rate (the Mbps figure advertised on the router) refers to the maximum wireless link speed between the router and a connected device — not the internet speed delivered by your ISP. ... Signal Rate means the maximum wireless link speed the router can provide. The wireless link speed is the internal WLAN connection speed between the computer/wireless client and the router. The signal link speed is different from the Internet speed.
tp-link.com/us/support/faq/2435/ - TP-Link, TP-Link FAQ 2435: TP-Link Router Internet Speed FAQs: Mbps, Link Speed, and Wi-Fi Explained (last updated 10 Jun 2026):
Different wireless clients negotiate different link speeds with the router based on wireless mode, distance, and noise level (interference from other wireless transmissions). In this example, 325Mbps means actual link speed, 1300Mbps means maximum link speed on 5GHz supported by our router.
tp-link.com/us/support/faq/2435/ - TP-Link, TP-Link FAQ 1865: Why the actual wireless speed on my wireless device is lower than the speed result on the Deco APP? (updated 2 Aug 2022):
Ceiling speed : The ceiling speed is the maximum theoretical speed of a connection standard determined in a controlled environment, without factors that would adversely affect the connection's throughput data rate ... Real-world speed : The actual transmitting speed, which is often less than the ceiling speed, as there are many factors would adversely affect the throughput of a connection, especially if it is a wireless connection. ... old generation 802.11n wireless clients are still widely used, their ceiling speed is only 150Mbps or 300Mbps
tp-link.com/us/support/faq/1865/ - TP-Link, TP-Link FAQ 2435: TP-Link Router Internet Speed FAQs: Mbps, Link Speed, and Wi-Fi Explained (last updated 10 Jun 2026):
The difference between Mbps and MBps matters: 1 MBps = 8 Mbps. ISPs typically advertise speeds in Mbps (mega bits ), while download managers often show speeds in MBps (mega bytes ). ... The 8M speed advertised by an ISP typically means 8Mbps.
tp-link.com/us/support/faq/2435/ - TP-Link, TP-Link TL-WR841N (India): 300 Mbps Wireless N Router, specifications:
N300 2.4 GHz: 300 Mbps (802.11n) ... 1× 10/100 Mbps WAN Port 4× 10/100 Mbps LAN Ports
tp-link.com/in/home-networking/wifi-router/tl-wr841n/ - TP-Link, TP-Link Archer C6 (India): AC1200 Wireless MU-MIMO Gigabit Router, specifications:
AC1200 5 GHz: 867 Mbps (802.11ac) 2.4 GHz: 300 Mbps (802.11n) ... 1× Gigabit WAN Port 4× Gigabit LAN Ports
tp-link.com/in/home-networking/wifi-router/archer-c6/ - TP-Link, TP-Link Archer AX23 (India): AX1800 Dual-Band Wi-Fi 6 Router, specifications:
AX1800 5 GHz: 1201 Mbps (802.11ax) 2.4 GHz: 574 Mbps (802.11ax) ... 1× Gigabit WAN Port 4× Gigabit LAN Ports
tp-link.com/in/home-networking/wifi-router/archer-ax23/ - TP-Link, TP-Link Archer AX23 (India): Ethernet ports, specifications:
Ethernet Ports 1× Gigabit WAN Port 4× Gigabit LAN Ports
tp-link.com/in/home-networking/wifi-router/archer-ax23/ - TP-Link, TP-Link Archer AX55 (US): AX3000 Dual Band Gigabit Wi-Fi 6 Router, specifications:
AX3000 5 GHz: 2402 Mbps (802.11ax, HE160) 2.4 GHz: 574 Mbps (802.11ax) ... 1× Gigabit WAN Port ... Actual network speed may be limited by the rate of the product's Ethernet WAN or LAN port, the rate supported by the network cable, Internet service provider factors and other environmental conditions.
tp-link.com/us/home-networking/wifi-router/archer-ax55/ - TP-Link, TP-Link Archer AX55 (US): Ethernet ports and speed note, specifications:
Ethernet Ports 1× Gigabit WAN Port 4× Gigabit LAN Ports ... Actual network speed may be limited by the rate of the product's Ethernet WAN or LAN port
tp-link.com/us/home-networking/wifi-router/archer-ax55/ - TP-Link, TP-Link Archer AX80 (US): AX6000 Dual-Band Wi-Fi 6 Router, specifications:
AX6000 • 5 GHz: 4804Mbps (802.11ax, HE160) • 2.4 GHz: 1148 Mbps (802.11ax) ... Ethernet Ports • 1× 2.5 Gigabit WAN/LAN Port • 1× Gigabit WAN/LAN Port • 3× Gigabit LAN Ports
tp-link.com/us/home-networking/wifi-router/archer-ax80/ - TP-Link, TP-Link Archer BE550 (US): BE9300 Tri-Band Wi-Fi 7 Router, specifications:
BE9300 • 6 GHz: 5760 Mbps (802.11be) • 5 GHz: 2880 Mbps (802.11be) • 2.4 GHz: 574 Mbps (802.11ax) ... Ethernet Ports • 1× 2.5 Gbps WAN • 4× 2.5 Gbps LAN
tp-link.com/us/home-networking/wifi-router/archer-be550/