Will It Work? · Guide

WPA2 vs WPA3: which security setting your router should use

By , founder of ElectronicsInfoline (since 2000)

The router's Wi-Fi settings page has a drop-down marked Security or Authentication, and it can list half a dozen options. Pick the wrong one and an old printer or smart plug stops connecting, or a new Wi-Fi 7 laptop runs slower than it should. This guide works through the options using the Wi-Fi Alliance's, Apple's and TP-Link's own pages.

Choose WPA3 Personal if every device supports it. With older devices on the network, choose WPA2/WPA3 Transitional (often called mixed mode): newer devices use WPA3 and older ones join on WPA2. Use WPA2 Personal (AES) only when neither works. Avoid WEP, TKIP, plain WPA and WPA/WPA2 mixed modes.

What WPA2 and WPA3 are

Both are Wi-Fi security protocols: they decide how a device proves it knows the password and how the traffic is encrypted. WPA2 came out in 2004 and WPA3 in 2018 (TP-Link). WPA2 Personal uses a pre-shared key (PSK); WPA3 Personal uses SAE (Simultaneous Authentication of Equals), and the Wi-Fi Alliance says WPA3-Personal users get more protection from password guessing (Wi-Fi Alliance).

A WPA3 network also turns away outdated legacy protocols and requires Protected Management Frames (PMF) (Wi-Fi Alliance). WPA3 is mandatory for Wi-Fi CERTIFIED devices (Wi-Fi Alliance), and PMF is required on all new certified devices (Wi-Fi Alliance). On the device side, Apple says WPA3 Personal works with every device that supports Wi-Fi 6 (802.11ax), and with some older ones (Apple).

Who can join under each setting

The setting is chosen on the router, and each device either supports it or does not. A router set to WPA3 only will reject older devices that only speak WPA2 (TP-Link). The transitional setting is a mixed mode that uses WPA3 Personal with devices that support it, while allowing older devices to use WPA2 Personal (AES) (Apple). Going the other way, a WPA3-capable device on a WPA2 network still connects, but on WPA2. So the only sure way to know what your network runs is to look at the router's own setting (TP-Link).

Which devices join under each router security settingWPA3 Personal only: device supports wpa3 joins on WPA3, device is wpa2-only rejected; WPA2/WPA3 Transitional: device supports wpa3 joins on WPA3, device is wpa2-only joins on WPA2*; WPA2 Personal (AES): device supports wpa3 joins on WPA2, device is wpa2-only joins on WPA2Device supportsWPA3Device isWPA2-onlyRouter set toWPA3 Personal onlyjoins on WPA3rejectedRouter set toWPA2/WPA3 Transitionaljoins on WPA3joins on WPA2*Router set toWPA2 Personal (AES)joins on WPA2joins on WPA2* usually: some very old devices may still fail in mixed mode
Figure 1. A WPA3-only network turns away devices that only speak WPA2. The transitional (mixed) setting uses WPA3 where it can and lets older devices join on WPA2. A WPA2 network takes everyone, but on WPA2, even devices that could do WPA3. * Some very old devices may still fail in mixed mode.

Which setting to pick from the list

Apple's router page puts it in one line: set WPA3 Personal for better security, or WPA2/WPA3 Transitional for compatibility with older devices (Apple). WPA2 Personal (AES) is for when you can't use either; if the router then asks for a cipher, choose AES (Apple).

The same page lists the weak settings to avoid: WPA/WPA2 mixed modes, WPA Personal, every kind of WEP, and any setting with TKIP in its name (Apple). Turning security off (None, Open or Unsecured) is strongly discouraged (Apple). The two mixed modes are easy to confuse: WPA2/WPA3 mixed is the recommended one; WPA/WPA2 mixed is on the avoid list.

Router security settings, from the one to choose down to the ones to avoidWPA3 Personal: newest; every Wi-Fi 6 device can use it; WPA2/WPA3 Transitional: WPA3 where it can, WPA2 (AES) for older devices; WPA2 Personal (AES): when you can't use one of the two above; WPA/WPA2 mixed, WPA, WEP, TKIP: weak: avoid on your router; None / Open / Unsecured: strongly discouragedchoose first ↑WPA3 Personalnewest; every Wi-Fi 6 device can use itWPA2/WPA3 TransitionalWPA3 where it can, WPA2 (AES) for older devicesWPA2 Personal (AES)when you can't use one of the two aboveWPA/WPA2 mixed, WPA, WEP, TKIPweak: avoid on your routerNone / Open / Unsecuredstrongly discouragedavoid ↓
Figure 2. Pick from the top. WPA3 Personal first; the transitional setting if some devices are older; WPA2 with AES only when neither works. Anything with WEP or TKIP in the name, plain WPA, and WPA/WPA2 mixed modes are on the maker's avoid list, and so is turning security off.

Open hotspots are a separate case. Wi-Fi Enhanced Open networks encrypt the data of each user even though there is no password, an improvement over traditional open networks with no protection at all (Wi-Fi Alliance). That is for public networks, not a home setting.

Wi-Fi 7 needs WPA3 for its full rates

A new Wi-Fi 7 router adds one more reason to keep WPA3 on. TP-Link says that under the Wi-Fi 7 protocol, the router needs to use WPA3 to negotiate 11be (Wi-Fi 7) rates with a device (TP-Link). Dropping to WPA2 only can fix an old device that will not connect, but some Wi-Fi 7 devices may then not get 11be rates (TP-Link). To compare the generations themselves, see Wi-Fi 4 to Wi-Fi 7.

Wi-Fi 7 rates need WPA3 on the routerA Wi-Fi 7 router and a Wi-Fi 7 device. With WPA3 on, they can use Wi-Fi 7 (11be) rates. With WPA2 only, some Wi-Fi 7 devices cannot.Wi-Fi 7routerWPA3 onWi-Fi 7 (11be) ratesWi-Fi 7deviceWi-Fi 7routerWPA2 onlysome devices: no 11be ratesWi-Fi 7device
Figure 3. Under Wi-Fi 7 the router has to use WPA3 to agree 11be rates with a device. Dropping to WPA2 only, to get an old device on, can cost some Wi-Fi 7 devices those rates.

When an old device still won’t connect

Mixed mode does not fix every device. Some very old devices may have trouble connecting even in mixed mode (TP-Link). TP-Link's Wi-Fi 7 router FAQ explains why: some older devices, especially certain smart-home (IoT) devices, cannot associate properly when the network offers two encryption options. Its fix is to set the band to WPA2-PSK only for the time being (TP-Link).

Before you drop the main network to WPA2, look at a guest network. TP-Link suggests putting older WPA2-only devices on a separate guest network, which keeps them apart from your main devices (TP-Link). The main network can then stay on WPA3 or WPA2/WPA3, which keeps Wi-Fi 7 rates for the devices that can use them.

Tips and tricks

  • Read the option names closely: "WPA2/WPA3" is the mixed mode to use, while "WPA/WPA2" is the one to avoid. Router menus put them next to each other.
  • Set every band (2.4, 5 and 6 GHz) on purpose. Some routers keep a separate security setting per band, and a smart plug that only uses 2.4 GHz cares only about that one.
  • After changing the setting, forget the network on each device and join again, so it connects with the new setting rather than an old saved one.
  • Changing the security type can knock every device off the network at once. Do it when you can rejoin them all, not in the middle of a video call.
  • If the router has no WPA3 option at all, check for a firmware update before deciding it cannot do WPA3.

What we would do

We would set WPA2/WPA3 Transitional on every band if any device is older or you are not sure what each one supports. If every device lists WPA3, we would go to WPA3 Personal. If one old gadget still refuses mixed mode, we would put it on a WPA2 guest network rather than drop the whole home to WPA2, especially with a Wi-Fi 7 router.

Choosing which band each device should use is covered in 2.4, 5 and 6 GHz. Whether a new router is worth it at all is what the router upgrade checker works out.

Questions people ask

Should I use WPA2 or WPA3 on my router? Use WPA3 Personal if every device on the network supports it. If some devices are older, use the WPA2/WPA3 Transitional (mixed) setting: WPA3 devices use WPA3 and older ones join on WPA2 with AES. Use WPA2 Personal with AES alone only when neither of those works.

Why can’t my old device connect after I switched the router to WPA3? A router set to WPA3 only turns away devices that only speak WPA2. Switch to the WPA2/WPA3 Transitional setting so they can join on WPA2. If an old smart-home device still fails, TP-Link says some older devices cannot handle the two options at once, and suggests WPA2 only for a while.

Is WPA2/WPA3 mixed mode the same as WPA/WPA2 mixed mode? No. WPA2/WPA3 Transitional is a recommended setting. WPA/WPA2 mixed mode still lets the original WPA in, and Apple lists it among the weak settings to avoid, along with plain WPA, WEP and anything with TKIP in the name.

Does Wi-Fi 7 need WPA3? For Wi-Fi 7 rates, yes. TP-Link says that under Wi-Fi 7 the router has to use WPA3 to agree 11be rates with a device, and that dropping to WPA2 only can leave some Wi-Fi 7 devices without them.

Do all new Wi-Fi devices support WPA3? The Wi-Fi Alliance says WPA3 is mandatory for Wi-Fi CERTIFIED devices, and Apple says WPA3 Personal works with every device that supports Wi-Fi 6 (802.11ax) and some older ones. Older or uncertified devices may be WPA2-only; their settings or manual say which.

Sources

Each figure on this page is quoted from the source below or worked out from them. Sources checked , each quote read again against the source in a second pass.

  1. Wi-Fi Alliance, Wi-Fi Alliance: Security (WPA3, Wi-Fi Enhanced Open, Protected Management Frames): WPA3 is mandatory for Wi-Fi CERTIFIED devices and includes additional capabilities specifically for personal and enterprise networks. Users of WPA3-Personal receive increased protections from password guessing attempts, while WPA3-Enterprise users can now take advantage of higher-grade security protocols for sensitive data networks. wi-fi.org/discover-wi-fi/security
  2. Wi-Fi Alliance, Wi-Fi Alliance: Security (what WPA3 networks do): WPA3 networks: Use the latest security protocols Disallow outdated legacy protocols Require use of Protected Management Frames (PMF) wi-fi.org/discover-wi-fi/security
  3. Wi-Fi Alliance, Wi-Fi Alliance: Security (Protected Management Frames): PMF is required for all new certified devices. wi-fi.org/discover-wi-fi/security
  4. Wi-Fi Alliance, Wi-Fi Alliance: Security (Wi-Fi Enhanced Open): Wi-Fi Enhanced Open networks provide unauthenticated data encryption to users, an improvement over traditional open networks with no protections at all. wi-fi.org/discover-wi-fi/security
  5. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers and access points (Security): Set to WPA3 Personal for better security, or set to WPA2/WPA3 Transitional for compatibility with older devices. support.apple.com/en-us/102766
  6. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers and access points (the three modes): WPA3 Personal is the newest, most secure protocol currently available for Wi-Fi devices. It works with all devices that support Wi-Fi 6 (802.11ax), and some older devices. WPA2/WPA3 Transitional is a mixed mode that uses WPA3 Personal with devices that support that protocol, while allowing older devices to use WPA2 Personal (AES) instead. WPA2 Personal (AES) is appropriate when you can't use one of the more secure modes. In that case, also choose AES as the encryption or cipher type, if available. support.apple.com/en-us/102766
  7. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers and access points (settings to avoid): These are weak security settings to avoid on your router: WPA/WPA2 mixed modes WPA Personal WEP, including WEP Open, WEP Shared, WEP Transitional Security Network, or Dynamic WEP (WEP with 802.1X) TKIP, including any security setting with TKIP in the name support.apple.com/en-us/102766
  8. Apple, Apple Support 102766: Recommended settings for Wi-Fi routers and access points (no security): Settings that turn off security, such as None, Open, or Unsecured, are also strongly discouraged. support.apple.com/en-us/102766
  9. TP-Link, TP-Link FAQ 5068: WPA2-PSK and WPA3-SAE: WPA2-PSK : Second-generation Wi-Fi security protocol launched in 2004, PSK means Pre-shared key. WPA3-SAE : Third-generation Wi-Fi security protocol launched in 2018, SAE means Simultaneous Authentication of Equals tp-link.com/us/support/faq/5068/
  10. TP-Link, TP-Link FAQ 5068: How to choose the encryption method for IoT devices on a Wi-Fi 7 router: However, the Wi - Fi Alliance finds that some older devices (especially certain IoT devices) cannot associate properly when faced with two encryption options because they cannot interpret the encryption correctly. To address the issue, it needs to temporarily adjust the encryption method to WPA2-PSK only. tp-link.com/us/support/faq/5068/
  11. TP-Link, TP-Link FAQ 5068: Wi-Fi 7 rates need WPA3: under the Wi-Fi 7 protocol, the AP needs to use WPA3 encryption to negotiate 11be rates tp-link.com/us/support/faq/5068/
  12. TP-Link, TP-Link FAQ 5068: WPA2-only and Wi-Fi 7 clients: Please note that adjusting the AP encryption method to WPA2-PSK can resolve client association issues, but some Wi-Fi 7 clients may be unable to negotiate to 11be rates. tp-link.com/us/support/faq/5068/
  13. TP-Link, TP-Link blog 2556: WPA2 vs. WPA3 (07-08-2026): A router set to WPA3-only mode will reject older devices that only speak WPA2. tp-link.com/us/blog/2556/wpa2-vs-wpa3-a-breakdown-of-wi-fi-s…
  14. TP-Link, TP-Link blog 2556: WPA2 vs. WPA3 (mixed mode and very old devices): Some very old devices may have trouble connecting even in mixed mode. In those cases, WPA2-only mode is still a reasonable choice, particularly when combined with a strong, unique password. tp-link.com/us/blog/2556/wpa2-vs-wpa3-a-breakdown-of-wi-fi-s…
  15. TP-Link, TP-Link blog 2556: WPA2 vs. WPA3 (guest network): You can also consider putting older WPA2-only devices on a separate guest network, which adds a layer of separation between them and your primary devices. tp-link.com/us/blog/2556/wpa2-vs-wpa3-a-breakdown-of-wi-fi-s…
  16. TP-Link, TP-Link blog 2556: WPA2 vs. WPA3 (check the router): A WPA3-capable device will still connect using WPA2 if that is what your router is set to. Checking your router's settings is the only way to confirm which protocol your network is running. tp-link.com/us/blog/2556/wpa2-vs-wpa3-a-breakdown-of-wi-fi-s…

Author: Bulan Sarkar · Report an error

Numbers here are quoted from standards bodies and makers, or worked out from them. Nothing on this page was measured or tested by us.